after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Dear All,
I am trying to implement a simple data recorder on nRF52840 DK that digitizes signals over SAADC and writes them onto the SD card. The program is working fine...
Hi,
Does anyone know where to find the BLE backwards compatibly of a given soft-device ?
I have looked at the PDF document given for my soft-device version S132, and...
Hello,
I am running an application on the s140 soft device using the buttonless dfu as an example. I am using the dual ramp pwm scheme to generate complementary pwm waveforms...
I'm having some issues with the 9160 on battery and wondering if we're doing something wrong or if this is expected behavior. During the initial connection to the tower, I...
We tried to adapt the RTC example from the SDK to add logging via UART during interrupts and the programmed crashed or hanged.
Here follows the code we are using :
The...
Hello, I have an application based on the example "ble_thread_dyn_mtd_coap_cli_pca10056_s140".
When a confirmable message has not received a response, I receive the error...
Hi,
We have built an iOS app with the iOS nRF Mesh Library ( https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library ) that collects data from all the sensors in the...
I am using nrf Toolbox iOS demo application. I have a requirement in which I want to change the incoming data stream to accept 4 bytes of data instead of the default 2 bytes...
Hello,
I am migrating our production code from SDK14.2 to SDK16, and switching to using FreeRTOS. During the BLE initialization and bonding, I get a system reboot. Tracking...
Hello,
Using an Arduino nano 33 ble which contains a nrf52840.
Using arm-none-eabi-gcc version 9.2.1 in debian/linux, uploading using openocd en gdb.
I tested my problem...
As I'm new to the nRF52840 and Bluetooth, I read documents and DevZone posts related to the bluetooth maximum throughput.
According to the references like Jimmy and Sigurd...
Hi,
I am trying to update from SDK 1.3 to 1.4 and struggling with crashes. COAP uses random number generator to generate new tokens to the header. First time when this...
Hello,
I use the default ble_template application from the SDK and download a BLE custom service template from here to add it to the template code (as described in the README...
