Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
We are using nRF9160 as the host MCU and Modem for communicating to server. If VDD_GPIO is powered by 3V external supply and SIM card is powered by VDD_SIM i.e. 1.8V Do we...
Hi,
I have a hex file generated by uVision Keil 5 IDE . I would like to combine this with the hex file form the soft device. These two hex files once combined would help...
Hi,
I would like to change the manufacturing data with time. My advertising_init function implements the following line
init.advdata.p_manuf_specific_data = &manuf_data_response;...
I've been using the nRF52840 DK to load the firmware into my custom nRF52840 board using nRF Connect v2.6.0 and programmer v1.0.2.
However, on another laptop when I install...
Hi,
We have developed a custom board using nrf52832 chip and currently everything like (BLE, TWI, ADC etc) is working fine but we are having issues with the UART. we have...
Hi,
We are using nRF52840 with nRF5 SDK ver 16.0.0 with Softdevice S113 ver 7.0.1.
We use the radio timeslot to implement low level radio comm with very tight timing requirements...
hi i am using this to capture the adc value data_ADC=adc_buffer[1]*(1024+gain_error) / 1024 + offset_error - 0.5; data_ADC_double=data_ADC*3.6/1024; MULTIMETER MEASUREMENT...
When I used nrF52832 mouse application, the SDK version was 15.3. When I connected to MacOS, I had to make several attempts to connect. Can you tell me why?
Thank you very...
Our nRF52832-based board is powered by a coin cell battery, and spikes in current can cause the voltage to drop. This is okay early in the battery's discharge curve, but as...
The communication between the UART peripheral and the nrf52840 works fine until some device connects to the nrf device via BLE. Using a digital logic analyzer I'm able to...
hello
now we want to use nrf52840 qspi interface to connect with fpga. we have a question:whether nrf52840 could be used as qspi slave, and fpga used as master?
if it...
Hello everyone,
I am a beginner with BLE and the nRF52, so I apologize in advance if this question is pretty simplistic. Basically, I am trying to achieve the most data...
Hi, while flashing devices in production testing our customer ran into the following problem. modemFW_flash.py got stuck in an infinite loop, making no progess but consuming...
