Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello,
I am using NCS v1.3.0 examples and also my custom made C++ code with Visual Studio Code V1.48.2 (Since the latest version of VS Code V1.5 is having official issues...
it seems that Figure 2 on this page https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fpwm.html is incorrect, or at a minimum the figure does not do what the...
Dear Nordic Experts, although the title says it all, please allow me to briefly explain the situation: I'm working on a ble mesh firmware and an accompanying Android app....
Hi,
I have been trying to run nrf9160: AWS_IoT sample on Thingy91 but have been getting the following output in the serial terminal:
I couldn't figure out what mqtt_connect...
The Situation: I am having a Sensor Node that is based on the nRF52832 (S132) and does two things: advertise some sensor data and store sensor data to the internal flash....
I'm porting an application that communicates BLE with a smartphone via nRF52 from SDK15 to SDK17.
It will be Connected, but I can only receive 2 bytes.
Also, even though...
NCS 1.3.0 mbedTLS configuration to the existing app in SES results in compilation error.
The SES project file contains the define like so -DMBEDTLS_CONFIG_FILE=\\"nrf...
I recently came across the Smart Remote 3 product by Nordic. I currently have a product in development that is a remote that has very similar functionality. Even down to the...
Currently I am facing an issue where the board was not able to power up by itself when a USB is port into it. However, when an external source is connected through the debugger...
Hello,
I have a costum board with nrf52832 chip. when I upload example code "/examples/peripheral/uart/" I can see logs coming and loopback test is working great, but when...
I am inquiring about a custom device that hangs in the ble_stack_init(); and the result is a fatal error.
The custom device has an nRF52832
The SDK is the SDK14
The...
Hi,
I am using NRF52810 which acts as a peripheral to send data to the central . The problem is my device is battery operated,So advertising all the times consumes battery...
Hi,
I have Design a new product based on the NRF52840 I am trying to get the lcd up and running so first thing is the pwm for the backlight. I am using pin 1.08 for the pwm...
Hello everyone, We're using a NRF52840 dongle for a Uni project. We got a couple of dongles it. I stupidly used a image on google to know the pinout because it's hard for...
I am trying to use the BluePy Scanner on a Raspberry Pi 3 B+ with a nRF52840-Dongle programmed as a Bluetooth: HCI-uart .
I am able to get the Bluepy Scanner code to work...
