Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello, developers! I am wondering if the Light switch demo and the thingy52-mesh-provisioning-demo serve the same purpose. I tried to run them combined: the first one on an...
Hi,
I'm completely new in the nordic development area and I'm trying to read sensor data from a DHT22 Temperature and Humidity sensor.
I'm used to directly include libraries...
Hello:
I am working on a USB bootloader project. I am running into the issue where the USB will not boot on first start up but boots following this. I read some of the previous...
It appears that there is a bug in the antfs.c sample code in version 15.3.0
nRF5_SDK_15.3.0_59ac345\components\ant\ant_fs\antfs.c
It the transport_layer_cmd_decode(...
I have a custom board using nrf 52382 with NFC. While Developing application I have checked nRF52832 Revision 2 Errata .
I have a question related [218] NFCT: Frame Delay...
Hello,
Our application runs over nRF52840 + SDK16 + FreeRTOS and we are using libuarte application to drive the UART. We found that the app_timer_freertos.c doesn't provide...
Hello ,
When i am using sdk functions with freertos some of the callbacks/functions requires (for example) xTaskNotifyFromISR() instead of xTaskNotify .
So how can i decide...
I am going to mass-produce beacons with built-in ble uart app sample.
However, I am not sure those produced beacons will have unique mac-address.
In my view, those are...
Hi all i am trying make a communication between esp32 and nrf52840 using UART. Initializing the uart driver was proper and pins also correct. when nrf start transmits then...
Using nrf52810 SDK 17 ble_app_hrs for my example, and i add some code about the passkey
Now the situation is after I enter the passkey on my Iphone nRFconnect app, and if...
As with my recent inquiry about a softdevice assert at PC=0x24e70 , I'd like to know which assertion fails in softdevice S132 version 7.0.1 at PC=0x157ec.
Is there a table...
Hello,
I observed a weird behavior when I changed to nRF52840-DK from nRF52840 Dongle. I am using the device as an SPI slave connected to a Raspberry PI as SPI master. ...
While trying to execute the light switch example, i was able to set the nrf52840 as evaluation board as proxy server but failed to do the same with the dongle.
2)When...
Hi,
When running the at_client example, I send the AT+CFUN=1 command via the LTE link monitor. After a few seconds, the nrf9160 reboots.
I want to say that before my program...
Hi all,
Currently I am working on my first project with the nrf52832. All is going quite well, but I would really like some help with my flash layout, basically I got some...
