Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I tried: - changing USB cables and ports (no any improvement)
- instructions from this link devzone.nordicsemi.com/.../nrf52-dk-does-not-show-as-a-removeable-drive-in-windows...
Hi there,
My question is similar to https://devzone.nordicsemi.com/f/nordic-q-a/39447/central-role-in-a-mesh-proxy-node , but perhaps slightly different in that my existing...
DFU Trigger Library (USB) is indicated that only for nRF52840 SoC. For other SoCs, can I use it after some modification of the library easily? What's the limits?
Hi !
I am on a firmware project for a nrf52832. I am using SES on Windows.
There seem to be a problem when combining buttonless DFU and NUS. When I do the services_init...
Dear devzone community,
I am currently in the process of migrating my MBED code to NRF5 SDK. My MBED code is functional and it works fine, you can find the code below: ...
There is no any Softdevice S122 listed on the page below.
https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK
We have downloaded the SDK from the same page...
Hey guys,
right now I am using 2 NRF24L01+ modules connected to two Atmel Atmega 644P in order to collect some sensor data and send it to a computer. Im coding via Arduino...
Hello, I am able to use the Zigbee CLI Agent and send some commands. I am using the zb-cli-wrapper python package to send commands from python. I wrote an application that...
Hi,
we developed a 2D-3D mouse .It contains a 2D sensor and a 3D sensor and 4 touchpads for left click,right click and 3D motion enabling.
The SDK we are using for developing...
Hi Nordic,
I am implement watchdog function in my nRF52840 project base on SDK15.3 ,but I found something I cannot understatnd, please help.
Watchdog reload value is 10000...
Hi,
I am trying to bring up open AMP application on nrf5340.
As previously known, this is used for exchanging specific data between the app core and the network core...
Hi All,
I am Working on nRF52840 and using nRF52840-DK.
Below is my working environment
SDK - nRF5_SDK_16.0.0_98a08e2
IDE - Segger Embedded studio (windows 10 -...
hello Nordic
i am working with nrf52832, sdk 16.0 , s132 (v7)
i am trying to send and receive data from an nfc reader/writer module (NXP pn7150)
if i use nrf_delay_ms...
Hi all, I am merging TWI code with BLE. I started with the ble_app_uart example working perfectly, however, after adding TWI libs and drivers (nrf_twi; nrf_twim; twi_master...
Hi All,
we were tasked by a customer to develop software for the nRF52840 and they recommended to use segger embedded studio. We downloaded it from the Nordic web site,...
