Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
In my current project, I am receiving multiple indications from peripheral device. After 25 indications, I need to pause the indications or disable the indications. I am using...
I have a question about "LE Secure Connections (LE Security Mode 1: Level 4)".
I recognize that it is impossible to realize "LE Security Mode 1: Level 4" when adopting ...
I want to realize "LE Security Mode 1: Level 4". However, there is no IO capability in both devices.
I tried the following. 1) Set the IO capability of both devices to ...
I have a question about "LE Secure Connections".
I recognize that "LE Secure Connections" includes the following security modes and levels:
・ LE Security Mode 1 Level...
I run eraseall but the following error shows up. how can I fix it?
nrfjprog -f nrf52 --eraseall --log ERROR: JLinkARM DLL reported an error. Try again. If error condition...
Hi,
We have a requirement of reading the BLE Advertising name from flash instead of predefining it in as a MACRO. I saw in the notes it says to use ble_gap_cfg_device_name_t...
Hi. I have just updated to the latest nRF Connect software for windows (v3.0.0), and the latest programmer app.
However now it won't connect to my PCA10056 dev kit (see...
Today I was playing around w/ my nRF9160DK 0.8.2 and messing around w/ the Asset Tracker application. I edited the proj.conf file in order to attempt to get it to connect...
I want to read data over uart from sensor, advertise the value go to idle mode and wake up on rtc timeout to do the same thing again.
when I try to read data over uart from...
The nRF52832 chip and SDK12.3.0 implement the buttonless DFU function.
First, as you are guided by the DK board, you have already completed the tutorial.
I tried to run...
nRF52832_XXAA, nRF SDK 14.0.0, SoftDevice 132 v5.0.1
We run a single service with 2 characteristics: one for "target to host" and the other for "host to target", where the...
Help ！
I use ANCS need change ATT MTU to more , but I met an incredible thing .
just change NRF_SDH_BLE_GAP_DATA_LENGTH to 189 & NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 185
...
Hi,
I was doing some current measurements and tried to reconnect my DK to my computer to put a new program on it. When I try to Connect J-Link, I get an error that says...
the link infocenter fail to download in:
(General PCB design guidelines for nRF52 series)
https://devzone.nordicsemi.com/nordic/short-range-guides/b/hardware-and-layout...
Hi,
Do you have a drawing of a recommended PCB layout footprint for the nRF9160?
I found a link somewhere, but the page didn't exist.
I need a drawing - not an Altium...
