Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I get "ERROR: There is no debugger connected to the PC with the given serial number." when I run e.g. nrfjprog --eraseall on command line.
Programming/debugging using VisualGDB...
Hi,
The User Guide v1.3 in Chapter 2 (minimum requirements) states "SEGGER J-Link Software" under "Software requirements". Is there J-Link software specifically for use...
I've been developing firmware for the nrf52840 for a few months using armgcc+openocd+arm-none-eabi-gcc working successfully. I recently upgraded my ubuntu version (18.04)...
Hi,
I am trying to connect to cloud MQTT (cute cat) which needs username and password for authentication. In the sample the password and username is set to NULL in client_init...
I'd like to create pc program connect to nrf51 device.
In Many document as I found, describe with dongle/DK and using a virtual com port like this.
PC -> dongle/DK include...
Hi,
I have some questions about application operation while in PSM / eDRX mode.
1. when modem is in deep sleep mode, is the application halted too ?
2. if not, what...
Hi, I am using nRF52 as a central SDK15.2 and SD132. I want to add in peripheral mac address which I want to put in the whitelist manually from the UART. But the example that...
Hi,
I read on the forum that DMA for UART block is not possible on nRF51. Is it true?
If yes, is there any way that we can enable this? Our application demands DMA for...
We developed device based on nrf52840 and android app based on nrf uart v2.0. The application runs very slow in google pixel 2xl., oneplus3 etc thich are updated to latest...
I'm working on certification for a product which uses an nRF52832 chip. I've found https://launchstudio.bluetooth.com/ListingDetails/14830 , which it seems I can use for the...
Hello,
I followed getting started guide given in the link below,
https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/getting-started-with-nrf9160-dk
I started...
(there isn't an option for nRF Android or Mobile when creating a case!)
Next to each Characteristic is one or more little arrow icons:
Where is the documentation which...
Hi,My lord. I use SDK 15.3 to run the example ble_app_rscs_pca10040_s132/s112 in DK PCA10040. My cell phone Samsung S9 runs the latest version NRF connect 4.22.3. But it can...
Can somebody explain the differences between the 2 git repos at NordicPlayground and Rallare regarding the nRF9160DK? Rallare has more samples of interest to me but I've setup...
