Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
Now i want to implement Scanning and Advertising at the time using s132 on nrf52832 with SDK15.0.
I use a app_timer of 10ms to realize a dvertising every 10ms....
I have an nRF52810 on a custom board and can't get it to wake from System Off mode. The code:
trying it with a different way to turn the system off also didn't work: ...
Dear Nordic Support,
Processor: nRF52840 / S140 soft device / SDK 15.3.0
I have a question about the use of the HFCLK in relation to the soft device. Our board has both...
Take a look at a following code
void fmc_serial_rx_cb(const uint8_t* p_data, uint32_t length)
{ __LOG(LOG_SRC_APP, LOG_LEVEL_INFO,"\n-------------SERIAL RECIEVED : %s...
I am new to softdevices so please bear with me for long list of questions.
I am evaluating SDK15.2.0 examples one-by-one. I came across eddystone example (ble_app_eddystone...
Hi!
In older SDK (15.0) has been present NRF_ESB_BUGFIX_TIMER and it initialization. Now (SDK 15.2/15.3) defines this macro but not use it. Is it bug or obsolete code?
Hello Nordic Team,
I followed the tutorial as you say( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/nrf52840-dongle-programming-tutorial ). But when...
dear all,
I'm a newbie on blue tooth low energy development, I have some really basic questions that I hope someone could answer, thank you very much in advance!
what...
Hello,
trying to bring up the new nRF91 dk with default firmware.
Registered the eSIM. Switch sequence followed when LED 3 and 4 starts blinking, but get the devices list...
Hi I have central device which has array of MAC address to connect.
when i see the structure of sd_ble_gap_connect() i cannot pass a uint8_t addr[5] as input.
so i tried...
SDK v11.0 & NRF51822 QFAC
I encountered a problem. In the process of pstorage processing flash data, a serial port interrupt came in, resulting in a system reset.
I used...
Hi,
I have discovered a (rare) problem where the S132 stack get stuck in connected state when it is not actually connected anymore.
This behavior was first reported by...
Hi,
SDK - nRF5_SDK_15.2.0_9412b96
HW - nRF52840 connectivity chip, other controller for application chip
We are tried to port serialization application on other than...
HW - nRF52840
SDK - nRF5_SDK_15.2.0_9412b96
We are running connectivity example in nRF52840 and connected UART with serialization application over UART which is different...
