Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am try to create a PWM output which can move the specified number of steps.
Please find following source code
After I execute above problem, I can get following...
Respected sir,
There is added external reset button at SRU532 module, and changes are given according to it using wakeup button at code.When wakeup button is used then some...
Hi all,
I am trying to implement a multilink central with UART. I had looked through the forum on all discussions in about this and followed this thread to come up with...
Hi guys,
I'm testing the 52810 duf function.
hardwar: 52810
using SDK: 15.3.0
softdevice: s112_nrf52_6.1.1_softdevice.hex
download software: nrfgo Studio
bootloader...
I am trying to flash the blink example from SDK v15 into my custom nrf52840 board, I am using pc10056 example.
I connected my ulink2 to swdio, swclck, gnd and vcc of my...
Hi,
Since the last update of the 'Getting Started Assistant' (0.9.0) from 'nRF Connect' 2.6.2 on Windows, I can´t set up or compile any sample of the SDK for the evaluation...
So I've been having a problem the last few days - using the NRF52832 we have an SPI chip connected his chip requires a clock signal (1MHz) that is being generated by the NRF...
We have written code based on SDK V12.2 and found it doesn't support power saving mode. Given that it's very complicated to transplant to higher version, how can we fix the...
Hi,
I want to interface two QENC with nrf52840, I saw QDEC example and it works as expected.
The problem I am facing is that QENC has four pins of which two are for power...
Hello,
I am having strange issue. I'm getting some data from custom service and characteristic. I can see the data being received is correct. However, if I try to pass the...
Is there a set date for the release of a tracker SW with working GPS? And secondly, will there be a step by step instruction how to upgrade the software on the dev. board...
Hello,
I'm an Embedded system student and I would like to make an extension for ZigBee for which I need to make changes to the underlying ZBoss stack.
Is it possible for...
Hi!
Most of the project's application code is written in C++.
SDK headers are guarded with the extern "C" therefore when including no problems arise with linkage.
The...
Hello,everyone
nrf52840,use sdk15.3.0, and I just want to run the example uart,but there is an error which is :ble_link_ctx_manager.h:no such file or directory. and then...
