Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
hello ,everyone,
I want to add the dfu service to the hrs example, but after I follow the step by step guide operation, I import the (settings+softdevice+bootloader+app...
I've tried to use Nordic Infocenter ( infocenter.nordicsemi.com/index.jsp) and it doesn't show documentation pages. It shows blank pages instead (see attached screenshot)...
Hi,
I'm using S132 SD 6.1.0. I'm transferring some advertising data to the SoftDevice and it returns INVALD_PARAMETER. How can I find out, where the problem of the SoftDevice...
Hi,
I got an issue with a battery powered sensor with generic OOB NFC pairing. The NFC is used to pair the sensor with a gateway, but if the device is not connected it must...
I just got the nRF9160DK. Followed instructions in video.
1. SIM card activated
2. Input sequence (push buttons and switches)
Expected LTE device added in nrfcloud ...
Hello,
I am developing an application that will eventually have quite a few different modules and I need to add timers to some of them. I use UART, I2C, SPI, RTC and some...
Hello,
I have a project where I'm using I2C. I want to configure P0.14 and P0.15 as my I2C pins as I already made a board thinking those would be available, however I get...
Hi, I am using SDK 15.1
My device is got hang during execution, namely in the function fds_init() - > while(!m_fds_initialized){..}
I wanted to reproduce this issue...
Hello,
Please can someone help me to undrestand this error while running other exemples in my nrf 51 DK with nrf 51422
PS: IDE : Segger Embedded Studio
SDK : NRF5_SDK_15...
Hello, I'm having a trouble over here, I read some tutorials for creating custom services and characteristics for BLE, and everything is running fine, I have a service with...
Hello,
I wanted to updated to SDK 12.2 and I noticed that FreeRtos is consuming 800uA in sleep!!! We do battery powered application and with this power consumption our battery...
Greetings Friends.
I'm having some trouble trying to figure out if I'm doing this the write way or not...
I'm developing a Eddystone scanner central on SDK15 with...
Hello,
I can not find any datasheet for the NRF52840-CKAA-R chip.
I need to know which GPIO pins have the constraint "LF" (low frequency only). Can I consider that the...
How the start address of my FW is set ? I would like to add a "library" right after the Soft Device. And the move the APP after this library. I can make it work when I have...
