Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi All,
I' ve successfully programmed an nRF52840 device with an application running with PHY_CODED modulation and I can scan it from my Samsung Galaxy S+. Unfortunately...
Hi, I'm running nRF5 SDK v15.2, and tried to run the led softblink example on port 1 of a nRF52840, which did not seem to work. I found a problem in low_power_pwm.c, which...
We want to use some device in the peripherial mode.
after the devices were bonded, for next connect I need to hide this advertise packet from air in the nRF Connect util...
We have a problem that we thought was isolated (affecting only one phone) until recently we started getting more phones exhibiting the same issue.
We are Australia based...
I can pair and bond as a Zephyr central via bt_conn_auth_register & bt_conn_security().
When the bond is successful I get a callback to cb_pairing_success(struct bt_conn...
Hello,
I am trying to read the internal temperature sensor using interrupts (SoftDevice is disabled). This is what I have:
#include "nrf_temp.h" #include "nrf_nvic.h"...
I am having hard fault when `nrf_sdh_enable_request` is called in BLE init. I am following BLE_TEMPLATE. I did not copy the solution, I am extending TWI example to include...
Hi,
I am trying to make a micro second timer count and I am using the timer driver from the timer example. However the timer init is failing in my code and I am not sure...
Hello,
I am using pc-ble-driver to write a desktop application interfacing with Nordic connectivity dongle. There is no automatic discovery module functionality so I have...
I am trying to just find what is this LE Secure Connection but can't seem to find anything basic. When i look at the lesc example, it look slike they simply turn the bit on...
Hello,
I am having a custom nRF52832-based central device - it works fine when connecting a single nRF52832-based peripheral (the both are based on SDK 14).
Now I need...
(added comment regarding intitialisation of GZP_PARAMS sunday 19 Aug)
I would very much like to use the gzp_dynamic_pairing package on the nRF52. Unfortunately I cannot...
hi, i am doing a project where i have to change adv name of ble device.
i am using nrf sdk 15.3.0 ble_app_blinky example for pca 10040e because it has all the things i need...
Hi,
I have created a new project and am following BLE_TEMPLATE. I want to learn, that is why I am not copying and pasting the solution and modifying - its the last resort...
Hallo everyone,
I'm using Eclipse IDE for C/C++ Version 2018-12 (4.10.0), my OS is Ubuntu 18.04.2 LTS and my hardware is the NRF52840 DK. I'm using the GCC C and C++ Compiler...
