after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi.
I am using SDK15.0.0.
I tested the RF communication through the ESB example.
And I have tested the BLE communication using the ble_app_hids_keyboard example. ...
Hello all
currently I am flashing the device using command line:
#erase chip nrfjprog --family NRF52 --recover #program softdevice nrfjprog --family NRF52 --program...
Hello,
I'm trying to read an ADC value from a sensor(for POC I'll be using a pot wired to 3.3V VDD and GND) but all the examples I found only demonstrated reading the internal...
Hi,
What is your recommended stand-off for your aQFN package to PCB?
Below image is from x-section after mounting nRF52840 to PCB, these are aQFN pads, could you advise...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello to everyonel.
I am working with the Light_switch example of Mesh 3.1 on nRF52832 (PCA10040). At this moment, I am trying to understand how I can send a message from...
Hello!
I want meashure pulse time via input capture.
I configured NRF_P0, NRF_GPIOTE, NRF_PPI and NRF_TIMER1.
It work fine, but in datasheet I found next text: ...
Working with NRF5 SDK 15.0.x, if I configure an GPIO as output, its initial state is low. I can set it high after configuration, but it is briefly low. Is there anyway to...
Hello,
I've got an nRF52832 embedded in a module (Telit RE866). As such, I can't see the markings on the chip and have to resort to reading the FICR registers to identify...
I'm working on a project where two devices are trying to get an estimate of the channel between them by taking RSSI measurements over a period of time. I am having a problem...
Hello,
I have custom board with nRF52840. Most of the time It works on USB power, but it also has a battery. It has some peripherals that powered via USB too (LED w2812b...
I've been trying to add UART support from the uart example to the ble_app_template example. I've enabled all the required drivers and options in sdk_config.h and included...
