after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
When I plug my PCA10031 dongle into a Windows PC, a Windows Explorer Jlink drive opens, then closes... then opens, then closes (repeat). This seems to go on "forever" (although...
I am attempting the use of Nordic's 802.15.4 stack with Softdevice in a multiprotocol way, but not using Thread or Zigbee. The application initializes sdh, then ble, then...
Hello everyone,
Currently I'm experiencing with some issues with serial bootloader in SDK 15.3. I'm using NRF52832 on my custom board together with main MCU that performs...
I am interfacing nrf52840DK to a SPI module soldered by myself on a custom PCB adapter, connected by wires. This is the init code:
I have two issues with the default...
Dear Colleagues
SoftDevice API has event NRF_EVT_POWER_FAILURE_WARNING but is missing something like NRF_EVT_POWER_RESTORED
My application needs to quickly check if power...
nRF52832-QFAA-0E, S132
With DCDC, UART and SoftDeivce enabled my ammeter shows 1.3 mA, but when app calls sd_softdevice_disable() current actually increases to ~4 mA
The...
Hi! Im just getting started With the NRF9160 DK. I have followed the instructions on "getting started Assistant" for NRF Connect (Windows 10). when im trying to build my Project...
I have a working/functioning project running on the nRF51 dongle that I want to develop for production. To save a step in FCC certification I am developing on an FCC approved...
Hello,
I am currently attempting to include mesh functionality in a bootloader so as to have it do DFU over mesh without the serial port. I keep getting errors when trying...
hi..... i am using nRF52832 and segger latest version 3.1 mesh sdk
i am trying to send the message from client to server side using light switch example , I have made some...
I'm testing this with SDK 15.2 on an NRF52832, with SD132.
The documentation says: "When the space is exhausted, write requests return the error FDS_ERR_NO_SPACE_IN_FLASH...
HI all
I am facing SPI cofiguration issue on nRF 52 DK.I am using PAJ7025R2 sensor and will act as a slave, and nRF52 acts as a master.Currently i am not getting any data...
Hi,
I would like to program a ble basic program on nRF51822 chip. I have Keil uvision MDK 5, ST Link programmer, SDK 8.0.0 and S130 softdevice + a third-party development...
Hello,
I have developed a prototype that uses the nRF52840 Adafruit Feather Express, a few sensors, and some other components. I am somewhat new to hardware engineering;...
