Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I downloaded the pc-ble-driver from github. I am using NRF52840 devKit and ubuntu 18.0 x86 machine. While compiling pc-ble-driver, I hit the following issue: Can someone pls...
Hello
I'm currently struggling with the LF_RC setup in sdk_config.h.
Calibration of the internal LF clock can be parameterized thru NRF_SDH_CLOCK_LF_RC_CTIV and NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Sorry, folks, for asking a newbie question. Well, maybe it isn't such a newbie question after all, but some gaps in the SDK documentation and examples. Specifically, I'm:...
Hey, guys, let me ask you a question. I have a device that does bluetooth broadcasting and ant background scanning. After working for 12 hours, the bluetooth broadcast frequency...
Hi, we are considering the nrf52810 for an upcoming project Unfortunately, the small flash size of 192 kB seems to be a limiting factor. The S112 softdevice and bootloader...
Hi,
currently I am adding DFU support to our application, I got everything working now, but only with the debug version of the bootloader (SDK15).
If I compile the normal...
Hi, maybe my question is a little basic, but this is my first time developing with a Nordic chip, i have been reading how to debug a nrf52 based device, and i know that i...
Hi,
I am using a central example to scan the peripheral and connects to it. I get data through notifications in bulk. That works fine. Then in order to add support to FONA808...
Hi,
I want to implement an MQTT-SN network with a Raspberry Pi 3B+ MQTT/MQTT-SN transparent gateway and some End-Devices in MQTT-SN.
This is working over Wifi with Paho...
Hi all. In my application i use display. So i need to store many fonts and images, because of that there not a lot of free memory left.
In which cases usage of mem_manager...
Hello,
I'm currently trying to connect Dongle nrf52840 to a Raspberry as a NCP. My issue is during flashing, I got a LIBUSB error when I flash the ncp usb_bootloader example...
Hi!
I have a problem with UART. SDK15. S132 6.0, nRF52832
I added UART to my project and watching strange behavior: when I attempt to send anything to UART
project...
Dear Nordic Tech Support and Developers,
Hello. I have implemented the Mesh Demo (light switch example) with Nordic Thingy 52. I would like to inquire an info on the side...
I'm using SDK12 and SES.
I compiled my code based on ble_app_uart example for nRF51822_QFAA and I see in Memory usage that RAM is at correct addresses (finishes at 0x20003FFF...
