Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,.
I have a question about using app_usbd_cdc_acm_read and app_usbd_cdc_acm_read_any in SDK15.2.0,
I am not sure I fully understand the description in reference...
nRF52832, SDK 14.0.0, SoftDevice 132 v5.
If SoftDevice is enabled but the system is not yet advertising or connected via BLE, will SoftDevice ever wake the CPU up from...
Although redirect.c is included and printf() calls use the uart as expected, fgets() calls don't seem to be able to detect incoming characters.
This isn't critical, since...
Checking QDEC (Quadrature decoder) of nRF52832.
But, In a SAMPLEPER Register(0x508) when set to 128us(0) or 256us(1) does not occur SAMPLERDY Event.
On the other hand...
Hi,
I am working on a project running on a nRF52832, using SDK 12.3 and S130. I use Eclipse (2018-12) as my IDE.
I have followed the explanations from this tutorial :...
Hi,
I am using a nRF52832 to communicate with a ICM-20948. I've been trying to write a 16 byte packet of data and read back and verify that same data. According to the ICM...
Hi,
I am trying to communicate from STM32 Nucleo board to murata's MBN52832, using SPI, with the nordic chip being the slave. So, for this I used the SPIS example from the...
Hi,
I am trying to get the ADC up and running on the nRF9160 DK. I had a look for example code and the latest I found was here.
https://github.com/Rallare/fw-nrfconnect...
Hi, I am using N52832 to developing a producation need to implements ANCS NC. I am using sdk 15.2. And I found the connection is terminated by the apple device after the reconnect...
I am using BLE peripheral UART application from nordic SDK version 15.2.0 SoftDevice S140 PCA10056 nRF52840 Development kit on Embedded Segger studio operating system - Windows...
I am trying to design some test cases to check the LTE stability and performance.
I avoid to use the existing Nordic samples to do this as they are too complicate for the...
I am migrating an existing project to nRF5_SDK_15.3.0, and I want to know why the error occurs and how to fix it ...
1. ..\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined...
Hello to everyone.
I'm working with nRF52832 SDK (PCA 10040) and Segger Embedded Studio v4.12, in the Light_switch example for Mesh 3.10. Right now, I'm able to use the...
Hello to everyone.
I´m working with the Light_switch examples (server-client-provisioner) in BLE Mesh 3.10 for nRF52 DK PCA10040. I´m trying to make a network with 2 clients...
The links I found regarding this go to a "OOps" page. I need the original FW of the nRF51DK so that I can use it to flash my target board using nRF51822.
