Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I want to let nRF9160DK communicate with an external module through UART in nRF9160DK
Then I need to assign rx and tx on two pins.
I will use UART0 for printk function...
Hey all!
I have a problem with my custom board using the nRF52832 with Softdevice 6.0 and SKD 15.0.0 working on Windows 10 in SEGGER with the BMD-300. I have the following...
We're using an nRF52832, SDK14.0.0, SoftDevice 132 v5.
Early in our firmware lifecycle, before SoftDevice is enabled, we configure our PMIC. This involves performing some...
I used SDK is nRF5_SDK_14.1.0_1dda907
Chip is nrf52832 evb.
Soft device is S332.
I call function sd_power_system_off() enter system off.
Use triggered from DETECT...
Hi..
I have try to lookup in devzone q&a, but seems not yet found the similar question or answer. Have try SR3 SDK and able to implement keyboard+consumer control for remote...
Hi Sir,
As runs w/ serial DFU and check the source code of nrfutil, it support to send the rest of page when transmitted the data.
1. If we don't want to implement this...
I want to advertise coded phy and 1M. This isn't possible at the same time so I am using the ble_gap_adv_params_t duration to timeout my 1M advertising every 600 ms to switch...
Hello,
I am building an application where client sends a fixed number of packets (10Bytes/packet) to a server with different values of advertisement interval. I changed...
Hi,
I'm developing a smartwatch that relies on low latency communication with local web servers. I'm in the very begining but I'm sure that the latency added between the...
Hello, I need to use MQTT over NB IoT with nRF9160. Task to connect to Amazon AWS over NB IoT with MQTT. As I understand correctly, NB IoT doesn't support TCP, so I can't...
Hi,
I was trying to download nrf5_sdk_for_mesh_v3.1.0_src.zip, which is at : https://www.nordicsemi.com/Software-and-Tools/Software/nRF5-SDK-for-Mesh/Download#infotabs,...
Hi all, I am working on a project for which I use nRF52832 with SDK15.2 and SD132. What I need is that nRF52 should transmit and receive command through serial UART as a central...
Hi, I am trying to setup a mesh architecture, and I am not sure which path to take (Thread / Zigbee / Etc). The architecture is for the following system.
There will be...
hello, i am trying an example of a Node running multi-peripheral with ble_nus service. I have a question: Suppose when Node receives a packet from central A, Node will call...
