Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hi,
I have created up to 5 custom services with several characteristics (4 at maximum) each one. They all use the same base UUID.
The problem I'm facing now is that when...
I am adding CLI service with my existing project developed based on ble_app_uart.
CLI Init function :
static void _cli_init(void) { ret_code_t ret;
#if CLI_OVER_UART...
Hi,
to be able to send more advertising data, i want to cyclical switch between different advertising packages. This already works so far.
Do i need to include the AD...
Hi there,
I am assessing the possibility of replacing a low-power MCU in one of our products with an nRF device.
Currently, our low-power MCU spends most of its time in...
Hi, all. I am trying to add a GPS module to the nRF52840 DK, just like what is done at this post. https://devzone.nordicsemi.com/b/blog/posts/nrf52840-long-range-demo
But...
Hello,
I want to write multiple words using the usb keyboard. I am working with usbd_hid_composite example on SDK_15.0.0_a53641a. I am able to write just a letter using...
i.e. it would be similar in type to the nRF24L01 radio code, but obviously different since it's part of the vastly different nRF52.
Any examples to draw upon?
Unable to get logging information for SAADC example project in SDK versions 15.0.0, and 15.1.0.
I have no problems accessing the logs for the ble_uart_app example project...
I want to do power profiling in my nrf nrf51822 devices. Nordic don't have any online tool to calculate current consumption for the nRF51 series. So how to calculate current...
Hello, We are using nRF51822, SDK12.3.0 and softdevice S130. It is a multiprotocol application using the softdevices' timeslot feature: Our protocol running in timeslots concurrent...
Greetings,
We are currently certifying a device to be compliant with FCC & IC rules in the US & Canada. The upper band edge measurement is failing on advertising channel...
Dear Support,
We are in pre-certification phase with our product using nRF52840.
For RF testing purposes, our testing house asked us to provide the following, and I am...
Dear Nordic,
I configure a GPIO pin to PWM output, from this diagram, if we enable `PIN[0].CNF.INPUT`, we can read GPIO status while the PWM is running. But I check the...
Hi
Am I alone in my judgement that some of the Nordic Example code is a good example of how NOT to code? These examples should demonstrate the perfect way to utilise a given...
I want to develop a custom Firmware for the Thingy:52.
I am using a Segger Edu J-link Debugger and the Thingy:52 PCA20020 Version 1.0.0. As an IDE i am using 64bit Segger...
