after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I'm using the UART / Serial Port Emulation over BLE example on the nRF52 development kit connected to a custom microcontroller.
I just need the nRF52 to simply relay bytes...
Hi everyone,
I have been looking for information about this, but I have not been able to find anything. I would like to send data employing UART, but I can not use the...
Hi, I have a few general questions on nus_data_send().
First off, is there another known way of transferring an array/string via ble to the Nordic mobile app other than...
Dear Sir,
I am working with nrf52832, SDK15 and s132 soft device.
I am using RIGADO DK .
Is it possible to continue advertising(from peripheral device) even after...
Hi All
I am doing a project which is base on SDK15.2 examples\proprietary_rf\gzll\gzp_dynamic_pairing\host\pca10040\blank\arm5_no_packs
I would like to add a timer to...
Hello,
I cannot add SPI0 to my application because OpenThread library was built with it without any interest of that. Could you fix it please ? (I need the 3 SPI peripherals...
Hello! I want to use the start time of the XOSC16M in NRF24LE1. I got ~4 ms. Can I put the processor to sleep at this time in standby mode? How to do it to wait for wakeup...
Hi all:
I see the "ant_share_channel _master_to_master" example,
this example is share_master,
my question is,
How to get p_ant_message[]?
the p_ant_message[]...
Is the recently released SoftDevice - ANT/BLE S332 SoftDevice v6.1.0 - compatible with the recently released SDK v15.2.0 ?
The supported SoftDevices listed in the documention...
Hello. A re-connection failure problem happens on our products.
chip:nRF52832 SoftDevice:S132 SDK v11.0
1. pairing and bonding on LESC 2. reset connection and re-connect...
Hi,
I have connected and SPI flash module to my pca10040 dev board. I wrote a test cycle of erase/write/verify for the entire flash and it works correctly. My initial pinout...
Hi,
I need some very simple file system to use on an external SPI flash. I gave a quick look at Flash Data Storage and it should be ok for me. I am not sure though why it...
Hi,
Disclaimer - this is definitely a question where one picture worth a 1000 words... ;)
My app use timeslot api to get a free time period to do some hard real-time...
