Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Using softdevice 6.1.0 and SDK 15.2:
Is it safe to use NRF_UICR->CUSTOMER[0] through CUSTOMER[5] for storing serial numbers?
It seems through in previous versions of SDK...
Hi All,
I have implemented the code for MASTER serial DFU in ST micro controller. which can send the app .bin file. I'm using 57600 baud and disable the flow control....
Hello,
I am using 15.2.0 SDK and 3.1.0 Mesh SDK.
I was trying to control two LED's on the nRF52DK using two generic level server models. I made following changes to the...
Hello. I got an nRF9160 DK with an iBasis eSIM that was already registered on an nRF Cloud account. Is it possible move the already activated eSIM to my Cloud account? I tried...
Hi Everyone
I have got 3 timers in my application.
1 is repeated , and other two are Single shot which are ran from the inputs to the 1st Repeated timer.
The repeated...
I'm developing for a custom board with an nrf52832. For one of my first tasks, I activated an on-board buzzer using the nrf_pwm driver. Then I stumbled across the low power...
Hi all,
I've compiled the SDK15.2 USBD CDC ACM example and uploaded it onto a Rigado BDM340 evaluation board, and run a second USB cable to the nRF USB socket. However,...
Hello,
We are trying to develop ble_app_uart with flow control enable, the problem is when we enable the flow control. if we send large number of data, the program get crashed...
Hi,
I am developing a product based on nrf52832 using FreeRTOS and the softdevice.
I use sdk 15 and I based my softdevice configuration on the ble_app_hrs_freertos example...
If the UARTE interrupt service routine is delayed from running more than 1 byte's worth of time, then APP UART FIFO does not see all bytes queued in the UARTE's easyDMA buffer...
Is there an API to get the dfu image size? We use this in combination with s_dfu_settings.progress.firmware_image_offset to show a progress bar on the gui. In the past, we...
The bluetooth mesh iOS app seems to be no more mantained since october 2018.
The main contributor of this project seems to have stopped working on it.
There are many open...
Hello I know you have IOS ( https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library ) and Android ( https://github.com/NordicSemiconductor/Android-nRF-Mesh-Library ) libraries...
Sir,
I am using a custom board, nRF52840 based MDBT50Q. I am working on the UART example program. In my board pin number 8 is used for some other purpose. And I have seen...
Hi,
I'm using a PCA10040 devboard to test the heart rate client example. I see that when using the example from SDK v15.2.0, I can connect to my (Polar) heart rate device...
