Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I'm building BLE preipheral and central devices for transmiting voice signal (best audio quality is not very important requirement) from peripheral to central. I...
Hi All,
We are in evaluation phase of a project where in our battery powered device would use nrF52840 MCU and communicate to the mobile phone over BLE (say about 5x times...
I am working on nrf52832 and sdk11. I want to store my accelerometer and gyroscope data into external memory.Does anyone have code of it? or any one having .c and .h file...
HI, I am using nrf52832 soc and i develop our own module. i need to create a mesh network within the device.
I am using segger embedded studio 3.34 (windows 10) and SDK...
I am new to BLE and want to learn what options and methods I have available to alter the advertisement package. Is it possible to include a floating point value, that could...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
Hi,
I am using pca10040 board of nrf52 dk. I am running battery level measurement code on board but whenever I observed values on serial monitor it shows garbage values...
Dear Developers and Members of the Forum
I have an Apple Macbook 6.1 (Late 2009) that has a built in Bluetooth Chip (Broadcom 2.1+EDR) and I want to use Xiaomi Mi Portable...
Hi,
I am trying to develop low power beacon on nrf52.
Which example should I base on?
I am trying example ble_app_blinky on PCA10040, and I am getting close to 1 mA...
Hi,
I have implemented the Master serial DFU code to update application and SD file. I'm following DFU packet send sequence. Ping, inti packet, FW packet.
I'm framing...
Hi,
I need to develop code for the custom board test, in which I need to enter the <channel> and it <power> value & then begin start/stop the continuous transmit the radio...
Hello,
Recently I purchased a nrf52840 Dongle to use it with nrfConnect for Windows.
I use nrfConnect 2.6.1. When I insert my Dongle in a USB port the LED starts pulsating...
Dear Sir,
We need a sample code for UARTE nRF52832 using EasyDMA. This sample code should drive our UARTE port using in BLE to UART mode. We could not find it by asking...
Hello, i am working with the nRF5 Mesh SDK on nRF52 based boards. Starting from the light_switch example i created a custom model to perform light control and other tasks;...
