Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi
working on a NRF51822 device with SDK12
I was using nrfjprog version: 9.7.1 to create a setting.hex with the following line
nrfutil settings generate --family...
i am using this project:
\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c\main.c as center.
nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\main...
I implemented the app_pwm_library, but it seems to "top out" at 500Khz? Here is a summary of my code. Is there a set of routines that have a higher speed?
APP_PWM_INSTANCE...
Good morning,
I already made a nRF51822-based prototype some years ago, and now I'm working on a new prototype but based on the nRF52840.
Is there any AN like the nAN36...
The design I am working with has no RTC. Is it possible to use nrf_drv_timer to "wake up" the CPU? I understand I will not be able to use app_timer code, so I was trying to...
Hello,
I am trying to use an interupt from an analog devices ADXL343 accelerometer.
With a power supply of 3.0V to my board, I only get a 2.1V on the interrupt, and I...
Hello! What does the real marking of the nRF24L01 + chip look like? I have not such, but very similar. The problem is that the module after a while ceases to go to sleep,...
I am using a STlink to flash a nrf51822 module , and i am using Keil to do that, i flashed the module but when i am scanning it to find it in my mobile i cant find it, i doesn...
Hi ,
Does the Application update depend on bootloader version? . I changed the boot loader but application remains same on my device , hence the device is not booting up...
I have an application with three other tasks beside the sdh task. I'm trying to integrate softdevice to my existing freertos application, but soon after the task scheduler...
Hi,
What would be the procedure for updating the firmware of device through another host micro controller UART? (Not with PC tools like nrf go studio, nrf connect, nrf jprog...
Sir,
I have a MDBT50Q-UFL evaluation board. I am using Keil uVision 5 and flashing is done through ST-Link. I downloaded the example files from http://developer.nordicsemi...
Hi,
I have Ublox EVK-NINA-B3 on table, which has totally different pin layout than NRF52 DK (not sure why): https://www.u-blox.com/sites/default/files/EVK-NINA-B3_UserGuide_...
Hello everyone! I am a beginner and I need help in understanding advertising data. I am migrationg from SDK 13 to SDK 15.2. In SDK 13, the advertising data with manufacturer...
