after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I have a product using NUS profile and plan to update it to support connection from multiple phone
Do you recommend to start from Multiperipheral example and...
if i use this code to send data,i sometimes miss data..
do { err_code = ble_nus_string_send(&m_nus, (uint8_t*)data, &data_len); if (( err_code != NRF_ERROR_INVALID_STATE...
I have nrfutil version 5.0.0. I run this command:
nrfutil pkg generate --hw-version 52 --sd-req 0xA8,0xAF,0xB7 --application-version 2 --application ./nrf5/Debug/nrf5.ihex...
Hello! We are trying to use Nordic AndroidScannerCompatLibrary in our Android application to scan BLE devices and measure its RSSI level. BLE devices is mounted on ceiling...
Hello there,
I would like to read the data I sent through a WS2812b LED string. I drove it using I2S. Upon reading it, seems like it is not a good idea to read it using...
Not sure what I did to cause this, but my nRF52840 no longer works. I searched for solutions and came across:
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52...
Hi,
I am wandering if it would be possible at all, to wrap a quarter wave antenna printed on flex pcb around a cylindrical battery (LiFePo4)?
Would the radiation be...
Hello,
Information:
SEGGER Embedded studio Studio v412
Windows 10
nRF52832 on a development board.
We are attempting to merge an application with a bootloader...
I have read that the nrf51822 is not supported anymore in the examples of SDK's older then V12.
Does the nrf51 completly not work anymore with newer SDK's or are only the...
I have my system working with softdevice compiled in but not enabled. System communicates with external chip using SPIM peripheral, everything is working fine until I enable...
Hi,
I have my custom board wired to the nRF52 development board. I am using SDK 15 and softdevice 132 for this. I am trying to set up SAADC to measure adc data on Analog...
Hi,
I'm only seeing the GPS_SIM driver in the nRF Connect SDK. Is there any driver to enable any evaluation of the nrf9160 on chip GPS anywhere?
Regards,
Kilian
Hello,
I have read numerous posts about NRF_ERROR_CONN_COUNT but yet able to solve this solve, my setup is NRF52840 Dongle as central and I want to connect to multiple Heart...
