Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I designed a nRF52832_xxAA board, use an external power switch, without DFU features its operating normally.
When I add the DFU function according to the Sample code...
Hi,
I am using nRF51822QFAA-R7 controller(DC DC setup) in my design.
I am generating +3.3V from rechargeable battery and providing +3.3V as a supply to drive these controller...
Hi,
I'm just getting started with nRF mesh (sdk V3.00) and I've built the light switch sample successfully and deployed it on three nRF52832 development boards but provision...
hello,nordic
I use NRF52840 QSPI+FatFs+USB-msc(..\nRF5_SDK_15.2.0_9412b96\nRF5_SDK_15.2.0_9412b96\examples\peripheral\usbd_msc),I found there is a bug about write to flash...
I am working on a new design for the nRF52832. I need to match an antenna to the device. My understanding is that the output impedance of the nRF52832 is 53 + J66 for best...
I am unable to toggle LED's on server boards, using Push buttons on client boards. flashed the light_switch client,server, provisioning images on nrf52832 boards using nrf5SDKforMeshv300src...
I programmed my nRF9160DK with the asset_tracker app using SEGGER Embedded Studio for ARM.
What I did was to open the prj.conf file and changed the following from "n" to...
Hi all,
I'm currently testing my Mesh network on a small scale. I'm sending messages every 25ms with different TTL values in an environment as visualised below.
The...
Hello,
I'm currently using an nRF9160 DK v.0.7.0 and the provided samples like the asset tracker and the at command client. Compiling, flashing etc. of the firmware already...
Dear Sir/Madam,
Can nRF Sniffer fetch the data of BT Classic Devices having any BT Version from BT 2.1 to BT 5.0?
Kindly help me on this issue
Regards,
MIHIR TAIL...
(running a mesh 2.1 sdk)
I am provisioning my nodes over serial and do not need the GATT Provisioning service. I need to access the GATT Proxy service to send mesh data...
I want to upgrade FW.
Android app has done. but only iOS encounter some problems.
First, I try to download nRF Toolbox on Github. result is DFU Service not found .
I...
Hi,
As per subject I am looking to implement hardware on-the-fly AES-CCM encryption/decryption of ESB packets. Are there any examples/guides available for the nRF52840?...
Hi,
With the PPK PCA63511 we have tried different PPK software such as python 1.1, nRF connect for desktop.
In that process we observed that current measurements are...
