after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Can the NRF5340's the network core on-chip Flash & SRAM be extended /utilised by app core so that app core can get more memory to run
Presently the WiFi integration with...
I started analyzing my application using SystemView to try to resolve a bug. I think I have configured everything correctly. However, when I start the analysis, I notice that...
Hi Nordic,
I am trying to merge nrf5 mesh serial and serial DFU, I have added serial DFU to serial mesh example, it is compiled successfully and do not show any errors...
I am currently working on a project utilizing the nRF52840 DK and dongle to measure distances between devices. In the process, I am leveraging the nrf_dm application, which...
NCS 2.6.0 nRF5340 project /ncs/v2.6.0/nrf/samples/matter/lock I want to enable APPROTECT on both app core and net core core. I want to enable it in firmware without UICR....
This question relates to using zcbor .
Basically I have the following.
I got The contents of FRAME - 00, 00, 00, 02, 00, 01, 01, 00, b0, 06, But I was expecting 00...
Hello,
we want to send a continous carrier with nrf9151 on dect-nr+ on a specific channel.
With bluetooth there is a testing option in nrfconnect tool.
Is there any...
Hi I would like some advice on where to start learning Nordic BLE?
All I could find by searching was advice from 6-9 years ago, I think today they are not relevant, because...
hello,
I'm doing a power consumption test, but I'm not sure which project to use to test the power consumption.I tried the "peripheral_lbs" download with NCS version 2.8...
My setup: SDK version: 2.5.0.v Modem version: 1.3.0. I am using MQTT to subscribe to a topic, for example, the LED state. The plan is t o set the LED state on the server side...
Hello, thanks for reading and happy holidays!
We are using an nrf5340dk, with zephyr and SDK 2.5.0.
We seem to have two undesired behaviors from MCUBoot immediately after...
Can,t flash nRF52832 custom board using nrf connect vscode extension im trwing to use nRFconnect for my project, im using fade_led from example and got this error
i try...
Hi everyone, I have a problem when I tried to configure UART ( baudrate, parity, data_bits, stop_bits, flow_ctrl). I upload my project:
#include "myuart.h"
#include...
