Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am using nRF52840 boards. I have one query.
I understand from your documentation that MPSL schedules the Radio driver to access the Radio. And BT ticker is for time slots...
Hi
I have flashed the unit with the Vysor flash file at Vysor Dongle · koush/vysor.io Wiki · GitHub The unit is now dead and has not recovered so I am returning to amazon...
I was planning on writing firmware for the nRF52840 chip (AKA System Controller) on the NRF9160 DK. Primarily it will use BLE and serial communications over some of the pins...
Hi, I am using nRF52840 and nRF Connect SDK V2.6.0
I want to send 7000 bytes of data using USB at a time. Now I am able to send only 1024 bytes at a time. I modified USB...
I'm using the nRF52+SDK11.0.0+s132. I'm developing a system that streams BLE notifications to an Android app at ~53kbps (40B/6ms). I have the connection intervals set to 7...
Hi,
I have a system I am redesigning to use the npm1300.
It has a rechargeable battery, about 3-4 weeks per charge, connected to an nrf9160.
The current system...
Hello,
I had to build the https_client sample again to compare some behaviors on my application and as I flash it to nRF9160 I am having a cyclical error as below:
...
Hello!
We decided to switch from NCS 1.8.0 to 2.7.0 for our products and at the beggining of everything, noticed something very strange.
Prepared very simple example of...
In my application using aws_iot library, the call of aws_iot_connect occasionally results in the following error messages.
[00:00:41.412,811] <err> aws_iot: Timed out waiting...
I have installed nrf-command-line-tools_10.24.2_amd64 and Link_Linux_V760_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hello,
I am trying to read ISM330DHCX accelerometer ( Adafruit product) data using nRF522832 but I am getting zeros all the time regardless whether the sensor is moved...
Greetings
I am trying to build the unicast_audio_server example application for an NRF5340 DK (Not the audio dk), as advised in this post .
When I try building the application...
Hi,
Currently, I am developing a project using the nRF52810 as my controller. I am using an emulated project of ble_app_uart with the SoftDevice S112. I have integrated...
Hi,
NCS Version: 2.5.0
Zephyr RTOS Version: 3.4.99
Zephyr Toolchain Version: 0.16.4
I attempted to build some of the sample apps for the nRF5340
Multiprotocol...
Hi,
I want to use nrc - latest version for linux. nrfconnect-4.3.0-x86_64.AppImage
However, I dont know how to install and dont find manual, guide to install.
Could...
