Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I implemented firmware update over LTE Cat-M and Ethernet last year by modifying the `fota_download` and the `download_client` examples into my own slightly modified version...
Hi,
I am using nRF52833-DK connected to my PC with usb cable for programming and debugging using the on board jtag.
In the beginning all worked ok, suddenly the jtag stopped...
Hi，
I have a custom board with nRF52833 and sky85303-21 FEM. To control the FEM, I have added the following code to my app.overlay file and enabled simple GPIO configs....
Hi everyone,
I'm encountering difficulties running my application on a custom nRF52840 board with a 48-pin package using Zephyr NCS version 2. 4. 4 in VS Code.
The problem...
Hi
Iam trying to make an ble advertiser project on nrf52840 with nrf21540(custom board)
there are a few configuration changes required for the board(pins and supply voltage...
I am programming with the nRF52840DKs. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am currently working on integrating...
Earlier I was using nRFconnect SDK 2.1.2. Everything works perfectly fine with that. Many features were added in that project. Now I want to port my project to latest SDK...
Hi Everyone
I'm developing a project using NRF52840 , the application needs OTA over BLE . It was working before without no issue , we tested in many devices and many times...
Hi,
I'm wondering if I'm missing something. I've been creating a bluetooth mesh light with hue, saturation, brightness, on/off, etc. models. However, my model_handler.c...
I have an app that uses the Nordic IOS-DFU-LIBRARY to drive the OTA DFU process with an Adafruit nrf52840 Feather running the Adafruit bootloader. I have the library setup...
Hello,
I am currently working with the Sniffer API provided in the extcap folder of the nRF Sniffer for Bluetooth LE package. However, I am unable to find recent documentation...
Dear Nordic support team,
We are using the SDK v2.6.1 to build targets for nRF52840 chips, and are using multiple configurations defined in a CMakePreset.json file.
It...
Hello,
I am trying to implement littlefs in my external flash memory. I am using nrf52832 and try to implement the littlefs sample code.
When I am trying to enable Config_spi_nor...
Hi,
I encountered a "Thread kick off too slow" issue. Let me explain it
My develop environment
Hardware: nRf7002-DK
SDK: 2.6.1
A. I copy the sample nrf/samples/net...
