Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I have this code developed for nRF5340.
Basically it scans for BLE advertisements based on the filters added and transmits the packets through UART.
Now for certain reasons...
Datasheet sampling rate is 100Ksps, but for me PPK2 always returns:
16384 bytes in ppk2_test.get_data() (one sample period)
4096 analog samples in ppk2_test.get_samples...
Hello Nordic,
I want to power down (at the lowest power consumption state as possible) all the peripherlas.
Already checked below ticket.
Below ticket also referenced...
hi,
I use softdevice s140 and nrf5_sdk_17.1.
I import time sync demo from here ( github.com/.../nRF5-ble-timesync-demo) to my project.
My first usage version:
* nrf52...
Hello,
I’m encountering an issue with my nRF52 device where it reboots during the flash_erase operation. Below is the relevant part of my code and the overlay configuration...
Hello all,
I'm using nrfx_spim_spis non_blocking sample to make my nRF5340 DK as SPI SLAVE.
I don't need SPI MASTER, so I delete the SPIM code.
But I found that I can...
Hi,
Is there any relationship between RTC peripheral and the system clock (which from DTC it looks like attached to rtc0)?
I'm trying to use PPI to generate a radio task...
I am looking for a solution of a multi-protocol controller for Linux host.
1. Coexistence of Wifi & BLE & Thread / Zigbee
The ble-coex / thread-coex example has the...
I'm trying to do a power analysis of an embedded device with a PPK2 and nRF power profiler and i'm running into an issue where i'm losing samples on longer capture periods...
I have a simple Thread joiner program. I am trying to join to a thread network created by my OTBR. Attached is my program. This program resets on call to otJoinerStart()....
Hi,
We use SDK 2.5.2 on a nrf9160. And have a hardware issue due to a too late update with the first boards. The GNSS LNA enable is wrongly connected to COEX1.
COEX0 is...
We are using eDRX to save power, but it seems like eDRX is not active always.
We currently use LTE_LC_EVT_EDRX_UPDATE callback to determine if eDRX is active. Is this...
I was modifying the download code sample in nRF connect SDK v2.6.1. I was attempting to download https//google.com/favicon.ico.
When I attempted to add the certificate for...
Now I am using the https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth/direction_finding_central/README.html and https://developer.nordicsemi...
