Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I am working on using the Nordic nRF TNEP API to support an NFC Bluetooth tap-to-pair application with negotiated handover. I have been working on programming the...
I'm working on custom test software for use in production programming/testing of my product containing a nRF9160. I'm using the nrfjprog executable, but with problems, every...
Hello. It's not charging at npm1300. The manufactured circuit did not have cc1 and cc2 of usbc connected to cc1 and cc2 of npm1300. If cc1 and cc2 are not connected, does...
I saw the recent announcements on your LinkedIn, that you're partnering with various NTN providers, that allow one to use LTE over NTN. However, how exactly do I access these...
I have a multithreaded application running on NCS 2.9.0 and I want to be able to see what all the threads are doing at the time of a crash via coredump. I have the following...
Hello team,
We are using nrf52dk with nrf52832 by vs code nrf connect sdk extension.
I have add zephyr led blinky application and flash it on the board and it's working...
Hi,
I like to analyze my custom BLE firmware thread activity, event, and timing using the Segger SystemView application. I have added the following configuration in prj...
Hello,
A super-simple piece of code that enables UARTE1 to receive a byte stream does not seem to work.
It seems as if nrfx_uarte_rx_enable() hangs up.
When I single...
I wanted to check if iOS 18 supports extended advertisements on coded PHY. I am not concerned with the advertisement payload limit but the increase in range that is possible...
I tryed to use the callback function provided by mgmt to hookit, but after including the header file` zephyr/mgmt/mcumgr/grp/img_mgmt/img_mgmt.h `, it prompted that "mcuboot_config...
Hello everyone,
I am currently facing an issue when trying to read data from a block of a Mifare 1K card. After debugging, I found that my program fails to authenticate...
We want to enable 2 way communiaction between Our Nrf9160 devices and server using Websocket secure. We used this as the starting point. We removed anything related to IPv6...
Hello,
We would like to interface an external PSRAM with nRF5340 MCU.
We didn't find any refference on how to do so.
So, my question is it possibel to interface...
