Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello Team Nordic,
Greetings of the day!!
We are currently testing the current of our device with the PPK2 kit.
We use the ESP32 as MCU and we are switching Cellular...
Hi,
I recently added the DEBUG_NRF preprocessor definition to my project because I wanted to use the nrf_assert module in some of my files. Now my project is crashing a...
In the nRF52840, I used the app_usbd_cdc_acm_write(&m_app_cdc_acm,tx_buf,size) method to output the data.
At the beginning, I use the pyserial to read the output data...
Hi,
I'm developing a software in python 3.9.6 64-bit which program a nRF9160 and nRF52840 using pynrfjprog.
The software is working from vscode debug session. But when...
Hi,
We are doing an analysis of power usage using a roaming sim vs home sim since the roaming sim data charges tend to be cheaper. (You wouldn't have happened to have done...
hi,
i m working to create a zigbee network using demo example of light bulb given in sample project of nrf5340dk.
as of now i am able to connect 2-3 bulb devices(i.e....
Hi, Using windows 10 OS, and SES v5.40. I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
I am running an application...
hi team,
working Environment:
nRF 52840 DK, SDK 17.1.0
keil uvision 5 IDE
os: Windows 10 pro
individually, I have worked on USBD and USBD_Audio examples.
now need...
Hi,
I am using an nRF52840 Dongle board and am not seeing any serial output. This is a board and set up I have used previously so I know the hardware is OK. I can download...
software:nrf connect sdk 1.9.1
hardware:nrf5340
hi professor,
I use the nrfx_gpiote_in_init(GPS_TS_PIN, &config_in, gps_timepulse_handler) but return NRFX_ERROR_NO_MEM...
Hello Nordic：
I wanna to know what actions a thread have done from reset to joined a thread network.
I observed the air packets by using Wireshark. I found a router(rx_on_when_idle...
The device is connected to the PC via FTDI chip. The device manager shows the COM port. LTE Link Monitor v2.0.1 cannot find the connected device on SELECT DEVICE. The windows...
Hello.
I am using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral and developing.
I am using nRF Connect to communicate with the peripheral nRF52832.
One of the...
