Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
HI , All
I am debugging connection of "Chromecast Remote Controller" with ble_app_interactive.
I am trying to implement ble_app_interactive on nrf52832 as my application...
Good Afternoon,
I am using NRF51822-QFAA as ble remote in central mode. It connects to ESP32 and send the command for changing it's mode. I am using the RF module YJ-14001...
hi
my board nrf5340 do not run any ble example . it creates build and everything is good in softwre while running. but when i try to receive any signal from board of blutooth...
Hello,
I am new with nordic boards. I am using an nrf5340-(P)DK.
I bulit and downloaded the perhipher-lbs sample successfully to the board.
However, when trying to discover...
Hello All,
I am developing thread base system.
I am using SDK - nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8
Dev-kit - nrf52840
I am using mtd code for development...
Hi,
My project is combined 'Multi-link Central Example' and 'ble_app_uart', so that it is a central that can be connected to multiple peripherals and a peripheral that can...
Hi, do you plan to upgrade FreeRTOS? In nRF5 SDK v16.0.0, there is FreeRTOS v10.0.0 - at the time of writing, FreeRTOS v10.2.1 is available and it comes with a few fixes....
Hi everyone
I am in the process of designing and developing a product. And I think there may be someone having some issues with connecting their displays to the NRF5340...
Hi,
I am trying to implement FOTA in my application. I can implement non secure bootloader and run successful
in prj.conf
in main.c
And Now I am need to add...
My team is developing an IoT application that transmits sensor data from the nRF9160 over the LTE-M network to a database. A few questions:
1. Is it possible to use the...
Hello to all,
I'm working on a project based on sending data collected from a sensor network to a Zigbee Coordinator: the sensors are End Devices and must be tied to a Coordinator...
hi professor,
According to peripheral project of nrf connect sdk 1.4.99, I add some function to achieve spi and usb and filesystem.But the ble run abnormal.When run bt_enable...
Hi,
When nrf_twi_mngr_schedule returns error as NRF_ERROR_NO_MEM what are best practices to handle that error. Do I re-schedule another transaction or is there a more robust...
In Our project we build a mesh network(about 100 mesh node)，before it work fine,but now we found can not access all mesh node through GATT link using mesh provision app. So...
