Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello I am using sdk17.0.2 and nrf52840.
I used nrf52832 to combine ble_app_uart and crypto_aes_ctr codes. And now I'm going to move the code to nrf52840.
However, there...
Hi! I made a custom board with an external flash memory that communicate with nRF52840 through QSPI. I have some boards that works very well, but i have someones that freeze...
I am trying to connect XBee 3.0 Zigbee to a Nordic USB dongle (PAC10059) which has the nRF52840 chipset.
I have been watching the traffic on channel 16 with a CC2531 sniffer...
Hello,
I've gotten the sample AWS FOTA to work on my nrf9160 using a very permissive public S3 bucket, but for production I need FOTAs to use a private S3 bucket.
According...
in fact the error that i posted is related to this file and exactly to the bloc in grey on nvic.h file
" C:/Users/rzaafouri/ncs/v1.5.1/zephyr/include/arch/arm/aarch32/cortex_m...
Excuse me
Prorammmer app in nrf connect for desktop Prompt no device available when I connect thingy91 to PC with mirco-usb cable,I want to update modem， certificate and...
Hi everyone,
We design an application using the nRF52840 and SDK16. This application is intended to be used for gait analysis and one of the requirements is a real-time...
Hello,
I'm trying to initialize the values of all my attributes using sd_ble_gatts_value_set . According to the documentation, the connection handle is ignored if the value...
Hi,
I unsecured my device and running it with JLink RTT to observe logging. If I program uicr registers during this process, the devices gets secured and I have to redo...
Hi,
I'm BLE-sending out Sensor values using a nrf52832. When the sensor gets a (new) value an interrupt is generated and the nrf then transfers the value in the gpiote inerrupt...
Hi. I have read the documentation and I have a couple of questions:
What makes work different mesh_gatt and nrf_ble_gatt? Why can't they work together (maybe it's because...
hi professor,
I add the CONFIG_NO_OPTIMIZATIONS=y but ble connection timeout In my pheripheral project .When I delete CONFIG_NO_OPTIMIZATIONS=y, the ble will connection...
Dear Nordic Team and Community!
I have again a question concerning advertising. Currently I am working with the devices nRF52840Dongle (Advertising, S140, 10059) and nRF52840DK...
Hi, I'm using nRF52805. My "1 button to turn ON/OFF system" code works perfectly fine on nRF52 DK.
However, when I migrate the code to nRF52805, Segger shows me an error...
Before exploring the Zephyr ecosystem, I plan to study in detail the periphery of my microcontroller (nRF5340).
For this purpose, I plan to try examples from nRF5_SDK_17...
