Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I'm trying to add a rotary encoder support to the HID keyboard example on SDK17.0 with some custom hardware utilizing the NRF52840. It works well to send the requested...
Hello,
We updated NFC in our product to use SDK 17.0.2 Type 4 NFC, and we are getting customer reports that reading NFC fails on devices which used to work just fine on...
I want to create mouse&keyboard set based on nRF52810's. Keyboard that will be used is from broken laptop with 24-pin connector. Does nRF52810 have enough pins for that? ...
Hi,
I have setup a device with usbd_cdc_acm to communicate with a computer throw usb port.
First, when the device boot up and the usbd init, all works fine and the device...
Hi, I need to select a BLE+ANT SoftDevice for nRF52805. I have read link1 (All nRF52 Series Protocol Stacks) and link2 .
Questions.
1) Why I cannot find S313 from link...
Hi,
Is there any provision in nRF Connect v3.7.0 tool UI to perform uplink data transfer test scenario on Nordic nRF9160 DK ?
Please let me know if there is any alternative...
Hello,
recently i made software for peripheral with custom service and five custom characteristics and everything works just fine. Now I want to make central capable of...
Hello all I copied the peripheral>twi_scanner example and adapted it to the nRF52833 chip on our custom board. I have 4 chips (0x0b, 0x48, 0x52, 0x68) that use I2C on the...
Hello,
What's the correct way to respond to MTU requests with pc-ble-driver-js library ? on a pair of nRF52840 USB Dongles, using nRF Connect for Desktop, project based...
Using the nRF Connect mobile app for iOS (version 2.4.12) we are trying to get the MTU that our nRF5340-based device is using, however it always seems to be wrongly displayed...
I need to send data over ModBus-RTU (basically RS485) from an nRF52840. For this, I use uarte. The transceiver's transmit enable input is controlled through a GPIO pin, which...
1. I've deleted the peers from the device by running the BMS sdk example, still i am unable to connect the previously bonded device where i"ve deleted the key.
2. The pm_evt_handler...
I get NRF_ERROR_FORBIDDEN error when I want to send a software message to the server device in the Light_switch application, except for the button. But when I press the button...
