Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I used exampl:
nRF5_SDK_17.0.2_d674dde/examples/ble_peripheral/ble_app_hids_keyboard
Why can't I see any HID Services in apps (nrf Connect) in iphone 12?
But...
Hi, I've read that when NFCT is operative the internal resistor of SoC is automatically adjusted. For antenna tuning this resistance can be set to a fixed value through a...
Hi there,
My current setup:
1. Custom board.
2. SDK nRF5 SDK v17.0.2
3. Application running BLE (SoftDevice)
Using the USB CDC Class example to be able to interface...
I'm using nRF51 sniffer to capture BLE packets for group of devices. Sniffer can able to capture only primary advertisement channels and not secondary advertisement channels...
Dear Members,
I want to use this code :
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk51.v10.0.0%2Fant_examples_bpwr.html
Does it work...
Excuse me:
As shown in the figure below, can this type of crystal oscillator be used on nrf52832? How to connect this crystal oscillator with XC1 and XC2 of nrf52832?
Hi,
we are preparing for certification and are about to test with the DTM v1.0. now in nAN43 it states following:
1.1.1 Hardware requirements • nRF8001 Development Kit...
I try to add pairing/bonding to the NCS hello world project. But I found the information is not easy to find. I'm playing with the bt_conn_auth_cb struct to understand how...
Hello,
I am trying to verify a signature with the `NIST p-256` curve. I had previously done this with the Nrf5 sdk and it is working:
I am now trying to migrate...
Hello Nordic Team,
as a newbie in the Nordic world, I have been reading the nRF Connect SDK and Zephyr documentation as well as testing some of the samples on my nRF5340DK...
Hi.
I have some trouble to use a sensor based on JDY-23 module with nrf52832 dk
(JDY-23 datasheet : ://fcc.report/FCC-ID/2AXM8-JDY-23/4936741.pdf )
We tried to connect...
Hi,
Is LLPM over the air compatible between nRF52840 and nRF5340 devices?
I am aware that LLPM is not fully supported yet on nRF5340. Also, any update on the LLPM support...
We are hearing solder bridge issues on the NRF52832-QFAA:
"Due to the high thickness of the copper layer and small lead spacing on the component, the boardshops are not...
I am working on customizing the DFU bootloader (to add encryption). When attempting to use the instruction trace in Ozone to debug, I see a lot of nonsense. One example is...
