Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi everyone：
New to the DevZone, nice to meet you guys.
I have an problem to the GPIOTE.
I'm now using an AFE4404 to calculate the heart rate and heart rate variability...
Hello, teams!
I'm sorry to bother you.
Now I'm testing mesh function.
I have two questions.
1) Is there good way to show the performance of relay operation?
...
Based on nRF52840 datasheet, to configure the QSPI peripheral, it is necessary to activate the external flash memory interface using ACTIVATE task. Our problem here is, during...
Hi,
I am using nRF52832 in a custom board for sending data. I need a reference voltage for my instrumentation amplifier around VDD/2, my VDD is about 2.7 V, so 1.3 V will...
Hi team,
Want to consult you on PA usage, my customer wants to achieve +16dBm PA, so if he has our 840 in +8dBm TX power, only needs +8dB for the PA or we would recommend...
Hi,
I would like to connect two centrals to one peripheral with >= BLE 4.3. I know,
normally one central is connected to multiple peripheral, but in this case,
a special...
I got an error when trying to build the dimming_client_nrf52840 example.
Simple error:
build/dimming_client_nrf52840_xxAA_s140_7.0.1_Debug/obj/ses_startup_nrf_common.o...
SDK 16, S132 V7.0.1, NRF52832, custom device, custom firmware.
Hello,
I want to keep beaconing advertisement (not connectable advertisement) while the BLE is connected...
Hi,
I have a question concerning the SIG qualification. We use the ublox BMD-350 (nrf52832) that is qualified as a component (QDID 101018). I don't really understand the...
Hello,
We are using nRF52840 chip with S140 with ble_app_blinky example.
I was merging Serial DFU bootloader, SoftDevice, application and BLE settings with below commands...
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of Thread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure these...
Hi,
I wrote my codes to toggle notification on and off using a button using nRF25840-DK and sdk v15. The task looked a simple one; however, I hit some issues such as error...
Hello Nordic Team,
We are working on a project based on nrf51822, we have a problem regarding the incorrect ADC values while waking up the microcontroller from System...
Hello,
I'm developing a custom asset tracker board. My software is currently a very lightly modifed asset tracker v1; my provider currently only support NB-IoT, firmware...
