Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I am developing a project related to transferring audio in low energy Bluetooth. I came across nrf connect sdk is the best one for LE Audio transmission
But I am familiar...
Spent a day to build the mesh nrfutil tool. Write down the key step for remind others
Build in windows, No idea for install py2exe in ubuntu python2.7
Use python2.7, do...
I m using nrf52840-DK Board.
For CTL example i got the perfect output on board LEDs 1 to 4.
Then i cut the solder bridge (SB5-SB8)and then used GPIO pinout for external...
I studing a project which is developed on ble_peripheral example. There is using nRF52832, sdk 15.3.0 and s132 softdevice at the project. There is a mobile device, nRF52 and...
Hello
NRF52840. SDK5 17.0.2
the function sd_nvic_SystemReset is define like this:
but NVIC_SystemReset is declared as NO_RETURN which cause dozens of "statement...
Hi,
we're developing a firmware for the nRF52811 that makes exhaustive use of RSSI sampling during packet reception. While this gives reliable results for Nordic proprietary...
Hello,
I'm currently using fatfs with a QSPI flash device on an nRF52840 with SDK 16. I was wondering what is the best way to put the qspi device to sleep in between reads...
Hi, i have a project with NRF52832 and i try to designing 2.4GHz antenna on PCB. I use your antennas as an example while designing, but whenever I try to simulate these antennas...
The company I work for wants to make a wearable personal (care)alarm device for use outside, think of an elderly person who is still mobile but is prone to falling. This device...
hi
All video I can found from youtube and nordic website :
(such as https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Mesh/GetStarted#infotabs )
are...
HI,
I'm facing a weird issue where the nRF52832 breakouit would reset and upon reading the RESETREAS reg, the value is 0xC or 0X8 ,I am using s132_nrf52_4.0.2_softdevice...
Hello,
I am using nRF52833, nRF Connect SDK v1.4.2.
I have imported the Zigbee light switch, light bulb, network_coordinator build and test it successfully.
I have also...
Dear Sir/Madam,
I have bought NRF52840 dongle to bring up my prototype as fast as possible. I am new to Bluetooth tech.
My application requires following peripheral...
Can we do CTL with dimming and generic on/off in nrf mesh app simultaneously. by using GPIO pins p0.15 and p0.16. for external leds. Is external led will get off. What will...
