Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Please help with writing to flash. If SoftDevice is off all ok. If SoftDevice is enabled, the sd_evt_get function always returns the value 5.
Here is the test code:
Hi!
We are developing a tracker based on Thingy91 using GPS and LTE. We're using the latest Modem firmware 1.2 and Zephyr/NCS v1.2.0
The GPS cold start until receiving...
Hi Devzone!
I'm trying to monitor the battery level of Lithium Ion battery.
I'm using SAADC to check the voltage of 3.7v 3500mAh Lithium Ion battery.
The battery...
when I am waiting for an event the current consumption is becoming ~180uA continuously.
I am waiting for an event using the following function
void deep_sleep(void) {...
Hi All,
I would know, is the NRF52 BLE Mesh Bluetooth 5.0 qualified or not. I did not find it anywhere. As I can see the in Cypress website, they clearly mentioned that...
Can somebody please measure and post the dimensions of the nRF9160 DK please.
Either they are not in the SPEC, or i cant find them.
either way W x L x H - would be appreciated...
Is there a way to specify which AIN should be used through the devicetree API? For example, here is a code snippet:
How would I use the devicetree API to replace the NRF_SAADC_INPUT_AIN6...
Hi
regarding the Nordic guidelines for aQFN, it recommends to use 0.305/0.61 for through hole via.
We are using 0.2/0.4 to avoid soldering bridge and non find any issue...
Hi,
I've tried the Heart Rate sample code (both from hex and source file) and in both cases, I encounter the same problem - constant disconnection. When it finally connects...
Hey, so I have been working on developing a BLE central device on a Raspberry Pi using the bluepy library. It's a pretty simple application, I just need it to scan and interface...
I tried to launch your example "Bluetooth: Mesh Light" using nRF5340 PDK and I failed. I followed this guide developer.nordicsemi.com/.../README.html . Also I tried to launch...
I am student and my question is in nRF52833 how the feature of direction finding can be used ? From my understanding it has one antenna which provide CTE or IQ samples that...
When playing with the NRF9160 samples (https_client and mqtt_simple, haven't tried others yet), I found a problem and workaround to that problem:
I'm not sure if it's a...
I'm trying to use the 52840 with a QSPI flash memory device (SST26VF016). The page program instruction to the flash uses 4 IO lines and the first byte (opcode) must be 0x02...
