Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello,
As per your given link in 1.2 Build and flash - using SEGGER Embedded Studio ( https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/getting-started/posts...
Hi,
It appears that at least one Mesh_v4.2.0 example (light switch) will not link under nRF5_SDK_17.0.2.
I managed to get Mesh examples to run under SDK_17.0.0 a while...
I have a new Bluetooth remote product in development that has a bluetooth stack that will incorporate HID, BAS, NUS, ANCS, and buttonless DFU services. I have the HID and...
Hi, I'm using nRF52832 Software Development Kit, PCA10040, S132.
I'm getting this error while trying to connect with my device in the "ble_app_hrs_c".
"Connection...
I have found a few "how to" on cofiguring Eclipse for application development on nRF52 devices. After some point things are not as described in this guides. So, Is there any...
I'm trying to create a read event whenever a certain characteristic is read. I used BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event to monitor that. I also set "is_defered_read"...
Hello,
I am developing a composite HID peripheral based on the nRF52840 that can connect to a PC either via USB or BLE.
I am using SDK 15.0.0.
Regardless of the connection...
When I build and run an example Bluetooth: Peripheral HIDS keyboard (it's the same for master branch and v1.3.2) using nRF52840 DK I faced one strange behaviour. To simplify...
I just downloaded the latest version of the pc-ble-driver hoping some of the bugs I had reported were fixed. The downside is the notes do NOT indicate they were addressed...
I'm working on an nRF52840 design where we may get away with only the outer pin row on the package.
However, one pin on the inner row of harder to reach pins seems important...
To the kind attention of Nordic support team,
I'm considering here a scenario where only a device and only an host PC are involved. They are ble bonded together.
Now,...
I have been working on receiving data from sensor using nrf52832 and I have been successful in getting the data and printing the same in the app. I have also been succesful...
Hi!
I am using an ASXL375 accelerometer with a nRF52832, and I am trying to figure out a good way to read the sensor data asynchronously (allowing the other processes the...
Hi,
I am using SDK 16 and nrf52810 pca10040e. I tried to build the example code for nrf52810 bootloader from the nordic example folder(examples/dfu/secure_bootloader/pca10040es112_ble...
Hi there!
I'm in the process of migrating a project from a nRF52832 to nRF52840 due to insufficient memory and of course some problems arise during the process. Most of...
