I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Dear all,
I have picked the Ruuvi project : https://github.com/ruuvi/ruuvi.firmware.c and change the configuration to adapt with nordic dongle.
But after flashing, my...
Hi,
I am evaluating LC example, I am using an occupancy sensor. So whenever there's an occupancy it's detecting and turning the lights ON. But even when there's occupancy...
Hi,
I have created an eclipse based makefile project for nrf51802 module.
The sdk version that i am using is 12.3.0, and softdevice S130 .
Taking reference of ble_app_uart...
HW setup is my boart connected to a windows10 PC with an uart link.
I tried secure_bootloader_pca10100_uart_ses_nRF5SDKThreadv4.1.0.zip example, with some modification for...
Hi All,
I followed this article and got eclipse to work. I can use debugger, single-step, place a breakpoint. All good.
I noticed that disassembly window shows opcodes...
Hello,
I am working on a project that uses Azure as a cloud IoT provider and the NRF9160 as a gateway-like device which is supposed to make simultaneous connections to up...
Hi,
Just wondering if it is possible to configure the UICR Customer registers after erasing and flashing/programming the nrf52832. The hex file used to program the device...
Hi Team,
I wonder the operating system which has been ported on nRF52840 DK, I found multiple IoT OS what nRF52840 supports like ARM mbed, Zephyr, Contiki, etc. But can...
Using NCS 1.3.1.
Why is nrfx_spim_xfer() asserting when using NRFX_SPIM_FLAG_HOLD_XFER flag and a ss_pin ?
When not using a ss_pin in the spi config but configuring with...
HI,
I was trying to update firmware on thingy 91 using MCU bootloader. Now when I trying to upload again it is keep showing one error.
Error while probing devices: Error...
Hello,
I'm using nRF52832 and SKY66112-11 PA/LNA connected to increase the range. I'm using nRF5 SDK 17.0.2 and nRF5 SDK for mesh 4.2.0
I followed this guide to use PA...
Hello everyone,
I'm programming for nRF52833, using SDK17. When I program for scanning filter (SCAN_NAME_FILTER and SCAN_UUID_FILTER) and debug, I got these errors. I don...
I have a ST link V2 with swd interface support. For one of our existing projects ( custom board ), we want to examine the current consumption of BMD-350 ( NRF52832 ). Hence...
I am currently tasked with programming the NRF52810 to boot up upon a button press and then sit and wait for further button presses to trigger various functionality including...
Good afternoon
According to the project requirements, two keys were added to the compiler settings for stricter project verification:
-Wsign-conversion - Checking for...
