Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello, I am currently building a wireless sensor network, and I am searching for a transceiver and not a complete system on chip. I was working using NRF24L01, and now is...
I tried to write in flash since a couple of weeks.. and i am not able to do it... I am using SoftDevice... so i think i have to use Persistent Storage Manager Where can i...
Hi Devzone:
I am using the example project "fsorage" on nRF52840.
I see the project specifies the range for the flash storage to be
.start_addr = 0x3e000, .end_addr...
Hello
I am preparing for Bluetooth SIG certification. I use nRF52810 / SDK15.0.0 / S112 6.0.0.
I've been helped by Nordic about QDID before.
https://devzone.nordicsemi...
Hi there
After initializing the SoftDevice S132 V6.1.0, I request the HF crystal by calling the function sd_clock_hfclk_request():
Later in the code, after a BLE connection...
SDK:V16.0.0
chip:52832
development kit:window+keil
I trying to combine libuarte and ble_central\ble_app_multilink_central\. My project work well in ble_central. But...
Hello everyone, I need to build a photo capture application.
And the CMOS sensor go through MIPI-CSI2 interface.
Is there any example code and library for nRF5340?
Hi,
How should the USB pins be handled in case I don´t want to use them? Should they be just left unconnected?
What about VBUS pin?
Thanks and regards,
Juan
Hello,
I got the issue to run the NRF9160 DK as an external AT-Modem. What I need to do is to issue AT-Commands over the UART, which control the NRF9160 modem through an...
Hi , I am running zigbee cli example code from sdk and configuring nrf52840 board as coordinator and trying to add xbee module to zigbee network. Coordinator is not accepting...
OK, a bit of confusion somebody can clear up for me, I hope;
Does NRF_SERIAL_EVENT_RX_DATA get sent when there is ANY data in the RX buffer, or only when the RX buffer is...
Hello
I am developing peripheral interfaces on nrf9160 dk, For I2C, sPI and ADC I am not able find exapmle codes. ALso could not find api required for the same to develop...
Dear nordic:
I am working on a tool which can collect data from multiple ant+ sensors with different device types,like a bike computer.
It allows user to assign up to...
I want to communicate with two nRF52 devices without pairing?
It is possible? Yes means kindly give the realtive examples.
Maximum data length...
Thanks.
Hello there, I need to ask if these two; NRF M 24L01+1712AB , NRF M 24L01+1609AH (one with external Antenna) are still supported and have official libraries , and if not supported...
