Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
Now I installed SEGGER Embedded Studio. But I got a activation key from SEGGER. I put the activation key into the IDE. After the I checked in the path "tools->License...
Hi,
I've seen the results of the power profiler, but I'd like to confirm this - with no other concurrent user CPU processes (standby/sleep), is the S132 softdevice guaranteed...
HI ,
I need the nrfutil commands used to generate the following zip file
softdevice only
bootloader only
softdevice + bootloader
softdevice + bootloader + application...
Hi,
I am using nordic semiconductor nrf52840 development board and segger embedded studio. I want to write a code to switch on led when button is pressed. Is there an example...
Hi at all,
nice to join the community
At the moment I'll try to initialize the ble_stack_init(). I use the Keil v5 with the Softdevice s132 on the nrf52832.
So the problem...
When make calls
with the intention of flashing the 10040 device, I get the following:
ERROR: The --family option given with the command does not match the device connected...
on nrf52810 datasheet current consumption:1.5 µA at 3 V in System ON mode, with full 24 kB RAM retention, wake on RTC,But Online Power Profiler,Idle current 1.1µA.Idle current...
I am following the "get started reference of nRF52840"
https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52840-DK/GetStarted#infotabs
I cannot explore...
Hello,
I have two quastions
(1)
I am trying to run nrf5-mpu-simple written by , but there are just Keil's examples on Github and I am working in SES. There is written...
Hello,
I have developed an application that transmits a string as a notification to the phone app whenever there is a corresponding command received from the phone app....
Hi
nRF52 dongle as beacon---- Code used ble pheripheral/ble_app_beacon/pca 10056/s140
nRF52840 DK as scanner ----Code used ble_app_uart_c_pca10056_s140
what changes...
Simple question:
Is possible a central to evaluate RSSI before connecting to a peripheral?
The idea is to make central device connect and bond to a peripheral only if...
I'm writing some DVT tests what I'd like to see the output from the test display in real time on a RTT log. By real time I mean that if a log statement prints something, I...
I've been running into an issue when running examples from SDK 15.2 (S132 6.1.0) on a custom board that uses a Fanstel BC832 (uses 52832 soc) module.
At the moment I have...
