after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I have been trying to figure out how to enable coexistence between Bluetooth low energy and the nRF7002 and I have some questions.
1. In the nRF Connect SDK documentation...
Using nrf5340dk, SDK v1.9.0
Want to add external RTC via I2C to wake mcu up via alarm, Facing Issue with I2C init.
I have gone through the suggested sdk fundamental course...
Hi,
When do you plan to update your Online Power Profiler Tool for cellular with nRF9151 device?
I just can see nRF9160 available for calculation.
Regards,
Hello,
I am working on an ESB (Enhanced ShockBurst) communication setup using the following hardware:
Receiver (RX): nRF5340
Transmitter (TX): nRF52840 MDK Dongle...
I am trying to compile hci_lpuart for thingy91_nrf52840, but I have these issue. hci_lpuart:
Any ideas on how to solve this? I'd really appreciate it. And if you have any...
I would like to add smp ota firmware upgrade to the matter sample project, can you provide me with the specific steps to do so, and in which path is the ota file compiled...
Good night,
I installed the VS Code/nrf Connect in my Windows 11 Prof.
I copied the "blink sample" and I tried to build it, but I am receiving
* Executing task...
I am following this example https://github.com/crfosse/ncs_projects/tree/main/peripheral_zephyr , both secure and non secure and I am not being able of making the non secure...
Hi,
I am using Mesh of 30 nodes with avg Current Consumption 6mA and 2mA in sleep mode(by calling k_sleeps) , timer is 1s timer is running to keep Real Time incremented...
Hi. I used nRF Connect SDK v2.9.1 to add OTA to the Peripheral UART sample application. The target is nRF54L10, but when I build it, the flash usage exceeds 50%.
If the...
Hi
I see i get a cmake warning with DFU enabled with the following message:
whats the purpose of this? should i just have it always enabled in my conf, or for prod...
Hello,Nordic team
I am programming with nrf52833 and ncs v2.9.0
While bonding with peripheral ,central report No memory to create new report.But my soc flash and ram are...
Since of the security issue, our 9160, are connecting to a private network (10.x.x.x) by the operator. While testing the FOTA function on this private network, the 9160 has...
Working with an nrf52805. Copied a simple example (peripheral_LBS) and found that RAM overflowed by ~2.2K I note that the nrf52dk_nrf52805 is not listed as a "compatible"...
Hi Team,
I am using nRF52840_DK to program my custom board but I am facing some voltage related issue from VDD pin.
Measuring on board it's giving 3.0V for VDD & GND but...
