Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Im struck at some point with some error, added all supporting file along with header files but still im getting error. Im using sdk15.3 pca10040 nrf52832.
please verify...
I have a NRF51 DK board, and can't get it to do anything with BLE (probably including any of the examples that require a softdevice) but I ran the blinky examples just fine...
I am using a ultra-miniature (BMD-350) series module from Rigdo which has the nRF52832 BLE SoC. It is placed on a custom board such that all pins from the nrf52 SoC are brought...
Hi,
My projects with Nordic chips thus far have been pretty simple, but now I would like to use an RTOS. My question is, do I use the FreeRTOS available in nRF SDK, or move...
Hi,
I have a problem with understanding, how bits in ble_gatt_char_props_t are related with Specification of the Bluetooth System v5.1 Table 3.5: Characteristic Properties...
If I use a breakaway for some debug pads which SWDIO and SWDCLK are connected to and then snap it off so the traces are no longer connected to anything, will this cause a...
I'm trying to run the https://github.com/NordicPlayground/nRF52-ble-long-range-demo on Fanstel modules with integrated AFE by Skyworks - BT840X(E) https://www.fanstel.com...
I'm trying to connect to an AWS MQTT broker I have set up based on the code in https://github.com/joakimtoe/fw-nrfconnect-nrf/tree/36532a8ca60bf7139a988b5cbb4e6cb47948a9fa...
Hello In this thread we discussed a possability of building a system with large number of conecctions. So, we need to get data from 30 peripheral nodes on one central host...
Hi,
I'm developing a product that should take an image of a low-resolution image sensor, process it and send the result via BLE.
The camera has an 8-bit parallel interface...
Hello, I was finally able to connect the board via LTE to my nRFCloud account. However, when I go through the getting started guide, specifically the programming a sample...
Hi
Now I use the SDK15.2+MESH3.10 build my project.
Because my firmware was very large.
Moreover I want to use the nRF Connect update my device.
So,how to integrating...
HI I started off to test all the drivers before the actual development process kickstarts.I tried using the TWI sensor example for an i2c driver check.I used a DS1307 simple...
Hi,
I'm trying to add an interrupt triggered event to my code (which is based on the experimental LPN example from the Mesh SDK).
Looking through the development zone...
Hello , I come from taiwan.
I am using ble_app_hrs_c to connect my heart rate watch
I can set m_target_periph_name to search for devices with the same name and connect...
