Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I am trying to port existing software to a custom nrf9160 board. I am using latest nrf connect sdk updated with git and west. Could somebody from Nordic comment about the...
I tried to increase the bootloader size by reducing IROM start address and increasing size but I always get the same error:
.\_build\nrf52832_xxaa_s132.axf: Error: L6407E...
I would like to perform FDS garbage collection only when it is close to being full. I can read the fds_stat to see the number of words used and the words freeable but what...
Hi all,
I would like to get the complete name from the connected peripheral by reading the device name characteristic (0x2A00) in the Generic Access Service (0x1800). I...
I want to use sys_time_get() on my ble app in SES env. but it looks like sdk 14.2.0 doesn't support sys_time_get() on SES env. So I'd like to use the similar function such...
Hi
Am new to the nrf52382 , Am trying to establish connection between nrf52382 DK as peripheral and nrf connect app as central,
Am unable to connect it .Please debug...
Hi, I am using nRF52832 with sensor, nfc , Softdevice S132 v6.1.0 and SDK 15.2.0 to advertising packets .The sensor is interfaced with nrf52832 using twi interface. I have...
I learned from the following support ticket link that for adding a pre-bonded LTK to the nRF52 bonding store, I can call pm_peer_new().
https://devzone.nordicsemi.com/f...
Hi,
I am trying out the udp_with_psm example from: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/udp_with_psm as a first step in sending...
Hi Team,
I planned to have product with this nRF52832 chip and now development was getting stopped because of known issues on SAADC on this nRF52832 chip. When I am seeing...
Hi. I am developing application that should work both ANT+ and Bluetooth. For bluetooth connection I am testing with nrf connect for pc, but I was wondering if there is similiar...
Ran in to a build error when using nrf_fstorage_nvmc.c: \components\libraries\fstorage\nrf_fstorage_nvmc.c(128,19): error : conflicting types for 'write'
nrf_fstorage_nvmc...
Hi,
I'm working with the latest software version of nrf52840.
Can you kindly specify the exact addresses of:
1. Flash usage of Softdevice
2. RAM usage of Softdevice...
Hi Team,
We are currently validating a BLE enabled embedded device. The device has an ARM Cortex M0 chipset and uses Dialog Semiconductor for BLE.
Could you please let...
When using the 0.7.0-15.alpha firmware release. What is the best application side code to go with it. Should still tag v0.3 be used of: zephyr, nrfconnect and nrfxlib?
...
