Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
We are evaluating a new design using the nRF52382 (currently on a Rigado BMD-350 module) and we will have to use the GPIO near the radio due to the number of GPIOs...
Hi all,
I want to provision my mesh network of light_switch demo examples form ble_mesh_sdk_2.2.0 using the nrf_mesh android application but when I did scan in the app none...
Hello,
I am using nRF52832 IC with softdevice and SDK v15.
I wish to make the MCU in sleep mode and then a couple of milliseconds (let's say 250ms) wakes up the MCU. For...
Hello,
This is a show stopper! I cannot get any Logging to neither the Segger Debug Terminal nor the JLINK RTT Viewer installed by nRF5x-Command-Line-Tools_9_7_3_Installer...
Hi, Just to say that the nordic devzone website does not work with Vivaldi navigator For example, this link below opens correctly with my opera navigator, while it fails with...
Hello, we are trying to implement PWM function with an incrementing/ decrementing duty cycle using a logarithmic function rather than linear function. Is there any predefined...
Dear Sir,
I wanted to connect the peripheral device to a phone which has highest rssi value(where multiple phones will be sending requests).
For that I have enabled...
in Mesh SDK v2, simple on/off model example, client node doesn't act as a provisioner.
But I still want to combine provision & client in the same device.
Is that just...
Hi all,
I'm reading the ble_peripheral samples of the SDK. I know start a advertising with the function ble_advertising_start();
Now, i know a central address, then i want...
I'm using the PPI to generate a PWM signal on my nRF51822, and I've noticed that TIMER_SHORTS is never triggered unless the timer interrupt is also active. I had originally...
Greetings,
I believe I'm seeing the same issue as this DevZone ticket: https://devzone.nordicsemi.com/f/nordic-q-a/23903/gpio-behaviour-during-power-down-nrf52832/94059#94059...
Hi dear all !
the Question is very simply,
1. What the real RESET VECTOR (isr table) , ROM address for nRF52840 MCU ? I mean what happened each time after MCU CORE reset...
Using a nRF52832-DK and nrfconnect-2.0 on Win 10 everything works well.
But using that with Ubuntu 18.04 requires more installation documentation!
1. it seems, that the...
How many GPIOTE Tasks can I use at the same time. I want to drive six different pins with six different tasks which are connected to three events. Each event generates two...
