Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi Everyone,
I examined the document about nRF24LE1 FOTA "nAN18 - nRF24LE1 firmware update over-the-air". The document is about update firm by nrf24lu usb rf adaptor. I...
Hi,
I found some sensor drivers under nRF5_SDK_15.0.0_a53641a\components\drivers_ext\, like hts221, lps22hb and so on.
Where can I find example for those driver?
Regards...
Can someone please clarify a few things!
I'm trying to get high bandwidth on some to and from phone transfers. I have control and data gatt boxes, control has the connection...
Hi,
i am doing a project where i have to discover multiple custom services on connected ble peripheral from ble central device.
i am using nrf52832 with sdk 14.2.0 as...
hello,
Now i have two troubles in NRF52832 Gateway.
1.Planning introduce：
The only function of NRF52832 Gateway is to scan beacons' advertisements. With beacons‘ number...
Hello all,
So I've ran into an unfortunate situation, our firmware team decided to ditch us just as we're about to launch our product. I got a dump from them including...
HI,All
Before I erase flash ,I must do memcpy(). I do not know why.
As follow, after i delete the function memcpy( (uint8_t*)&data_buff[0], pdata, len), when i write data...
I have been trying to execute a simple program for GPIOTE event. I am using SDK 15.0 and using the nrfx_gpiote li"brary. I have added the required headers.
Yet, I am getting...
Hello,
I have a product in the field (sdk 12.2 and soft device S132, based on NUS profile) since a couple of month that works ok but crash with some Samsung devices
...
Hi I am trying to write a driver for the nrf8001 BLE and interface it with LPC1758 Arm M3. I am a beginner in this field and I am not exactly sure, if I am following the correct...
I try to port LESC example from PCA10040 to PCA10040e(52810) on SES.
Porting work has been done. When building, it reports VFP issues of liboberon_2.0.4.a, as below:
...
Hello all,
I am using the latest SDK 15 and softdevice v5 (downgraded from v6 thought it was causing issues) on the NRF52 DK. When I build my application it states:
Compiling...
I want to make my device automatically go to sleep mode when the power is connected. And when the device wakes up from sleep mode, it should not automatically go to sleep...
Hello, We are trying to use the debugger tool on Keil for the nRF51 DK, But we are having a really hard time to figure out how to make it work. Do you guys have a tutorial...
