Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
in the demo of EnOcean switch translator client,there is just enocean_switch_nrf52832_xxAA_s132_6_0_0.emProject .is it use the same demo as client in the example of light...
Hi, I am using nrf SDK for mesh and try to add FreeRTOS , but after adding build failed because both has files with same name. Is it possible to work with FreeRTOS and nrf...
Hello;
I want to scan beacon devices (UUID infos) every second with Arduino Uno + nRF51822
I could not find a sample on the site. (Arduino Code)
Is it possible? Would...
I've gotten a good handle on how Gazell interacts with devices and the host, but I am running into an issue where there are higher rate of failures when using two devices...
I am using the proxy server and the proxy client example
Initially Proxy Client and Proxy Server are present in MESH network. Once the Proxy Client recycle the power ...
What was the reason for not making the context available for saadc-handlers?
Most handlers I stumbled on (twi and timer) either had a void* p_context or void* p_user_data...
Hi,
We are using nordic nRF52832 in our project as per our requirement we have to implement sleep and wake up mode with the help of button interrupt.our use case is that...
Hello,
I am using sdk12.2.2 and customized board. I am using app_error_check after every api so that my code reboots if any of the api fails. I want to know should I use...
Hi all,
Is there a software way to detect if an external 32kHz XTAL is connected to the nRF52 or not ?
So it could possible to select the internal RC oscillator instead...
Hello,
I have a project that requires the use of the SAADC module for temperature measurement from an NTC Thermistor.
However, I will also like to use the CapSense touch...
Hi,
With reference to https://devzone.nordicsemi.com/f/nordic-q-a/33890/get-x-y-z-values-from-lis3dh-using-nrf52-development-board this thread. I am trying to get data from...
Hello,
My application is really close to the example named BLE relay example in the DK. We could start from this example and adapt it to our needs. The problem is that this...
I have the Adafruit Sniffer which is based on the nRF51822 Bluefruit LE Friend, which contains the Raytac MDBT40 . After searching and finding the CP2104 drivers, I can speak...
I have been reading the forum and there seems to be differing advice to use Timers or RTC, since TIMER0 is used by the soft device, so it could cause issues since the SAADC...
