Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi all,
I am using an nrf51422 DK as a peripheral, with s130 softdevice and sdk11 on Keil, and iPhone6, with iOS 9.3.1, runing nrf Toolbox UART app.
I am sending data...
Dear All,
NRF 24L01 communication fails particularly @ midnight / early morning 1:00AM to 3:30/4:00 AM and resumes Automatically.
In my project, I have 1 base station...
I was reading a line of code:
mesh_gatt_evt_t* p_gatt_evt = (mesh_gatt_evt_t*) p_ble_evt->evt.gatts_evt.params.write.data;
And ble_gatts_evt_write_t::data is the cenerpiece...
Hi, I'm an undergrade student.
I use Android-NRF-UART in GitHub/Nordic.
I want to enter the encryption about send message and decryption about receive message.
so...
Hi all,
I wanted to know the power consumption in ble device while advertising as well as while scanning. please if anybody knows about it, let me know soon.
Any help...
Hi
I am trying to start an advertise. If I use the “BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED” flag all work’s pretty fine, but whenever I change the flag to “BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE...
Is it possible to have a fast advertisement interval (for connecting and bonding/pairing) for example: 40msec; at the same time, have a slow connection interval (after connection...
uint8_t flags = BLE_GAP_ADV_FLAG_BR_EDR_NOT_SUPPORTED |
BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;
And then when I look up "BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE;...
Hallo,
i'm trying to test my BLE aplication using the PTS. The profile test are mostly OK. But if i run the GAP Test (especially TC_BROB_BCST_BV_01_C) the PTS does not...
It seems that static and global data is NOT set to zero during start-up. This is supposed to happen according to the C-standard. How to do this in a proper manner, i.e. to...
Hi All,
we currently move our custom design to CE testing and already did some successful EMC pretesting.
However, our testing house asked us to prepare a firmware for...
Hi All,
BLE Nordic Stack: 0.9.7
Tiny Circuits: Ardunio + Nordic nRF8001 Board
First time post, and hoping someone has run into the same issue that I am. I am in the...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
