I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
I have created files before with s110 sd8 with the
nrfutil.exe utility using a bat file.
nrfutil.exe dfu genpkg --application nrf51422_xxac_s110.hex --application-version...
Hello,
I want to connect one board trough SPI to my nRF51-DK. Using SDK11 and SD130, the nRF51-DK is the SPI master, I call the function nrf_drv_spi_transfer() but the...
Hi ,
In my project , i can use the battery service in my project.
But if i want to use the another four ADC channels , how to add it ?
my project is working at SDK 9...
Hi,
I am using 2 nRF52832, one for ESB Tx and one for ESB Rx used to send payload through UART using SDK11.
Tx board is used has a low power transmitter which transmit...
hi all,
i am a begineer to nordic. i want to send data over ble and read that using master control pannel.
please say wat api i want to use and how to use. please give detail...
Hello I'm new of nRF seriese.
nRF51822CEAAD00(0x004d)
SD130 ver2.0.1
kail Ver5.18
SDK11.0.0
I just finished the tutorial and now I'm making my new project with twi...
Hi, I am using Heart Rate rate monitor code to send floating value instead of unit16_t.
I am using the heart rate service to send the data. Instead of using simulated sensor...
Hi,
I am new to nRF5x BLE devices.
I need to create a project and would like you to help me out.
I need to connect two nRF51822 devices. If one of the devices goes...
hi dear officers
since the datasheet states that value 1 stand for connected, does it mean this pin is active-low.
in order to physically reset the device, could i connect...
I have tried ble_app_uart_c project in SDk 9 , SDK 10 or SDK11 , but they have the same problem.
Problem is that slave(SDk 9,ble_app_uart) can send data to master(by terminal...
While trying to bond an iPhone 6 (running nRF MCP App) with an nRF52 with S132 2.0.0 I encountered the following error:
On the first try, when the iPhone is not yet paired...
I am trying to set up a button interrupt by adding the following functions:
void button_interrupt_handler(nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_gpio_pin_toggle...
Dear Sir,
When nRF51822 is a slave, it should be updated software through Master(Z-Wave CPU) remotely.
How can we update SoftDevice software in nRF51822? UART, SPI, or...
My code detects an external signal using GPIOTE. Whenever the signal falls, GPIOTE calls a handler, audio_stimulus_handler . The code is shown below. Essentially, after detecting...
