after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I need to interface a LED driver (PCA9632) using TWI.
In the TWI APIs I can't see any way to pass the slave address to the TWI instance. Speaking about the nrf_drv_twi_init...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hi, I have an nRF8001 on a Red Bear Lab BLE shield mounted on an Arduino Uno. I'm using BLE to trigger the execution of potentially long running (well, a few seconds anyway...
Hi,
I've done a fair amount with the NRF51822 and Keil on Windows but decided it was time to switch to my native Mac instead of the VM!
Reading all the guides around...
Hello everyone,
I'm a beginner and i'm trying to debug a nRF51422 BLE project.
The SoC is supposed to wait for commands from a STM32 in order to execute some functions...
Hello,
I'm a newbie in this area, and I'm trying to program NRF51822 QFAA on a custom board according to the given tutorial for a dual bank bootloader ( devzone.nordicsemi...
Hello,
Since I am still a little confused, could anyone tell me what S110 and SDK I should use for nRF51822 QFAA? ( infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
i am going to buy nRF51822beacon but i do not know what to buy with it ?
i will buy nRF51 DK but i also want to use a segger programmer with nRF51822beacon.
what confusing...
I was wondering if you could advise me on the best way of adding in BLE functionality to an existing ANT application. Is it simpler to have both transmitting at the same time...
Peripheral receives 4 bytes from central in order to set color of 5 LEDs (1 byte command type + 3 bytes RGB data). There's an iOS app with color picker where user can select...
hi every one.
I need to load softdevice to nRF52 preview DK before execute this app follow it, but i don't know exactly how to do it.
This is my solution:
open...
Hi,
When I reset my nrf51822 beacon firmware using nrfgo, it works just fine. When I try to reset the firmware using jlink, I end up having problems. There are no errors...
Hello, I have downloaded the nRF_MDK_7_2_1, and open \Keil_v5\ARM\Device\Nordic\nrf51822\Board\pca10001\s110\ble_app_beacon\arm\ble_app_beacon with Keil_v5.
I set IROM1...
Teaching myself the Nordic libraries and API for nRF51 - going smoothly.
Keil uV5 and Dongle and SDK 9.0.0
Wanted to send my own data in the characteristic for HRM service...
