Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi team,
I am using nrf SDK 17.1.0 and using visual studio code editor with GCC compiler as IDE. I want to use nrf connect extension and use the advanced debugger features...
Respected Sir / Ma'am
We are trying to out the Locator Tag application
Successfully built and programmed the code on the nRF52840.
I can see the pop-up on the Google...
I'm working on optimizing power consumption in my project (using nRF5340DK; as well as Power Profiler Kit 2 which is connected to DK's VDD measurement point as an ampere meter...
Good Day All,
I'm having troubles with my nRF52840. (Specifically the nRF52840 18010 Holyiot module [http://www.holyiot.com/tp/2019042516322180424.pdf]) I've designed a...
I am looking for the nRF9151 variant of this document nan041: nRF9160 production programming . I do not currently see anything available on the technical documentation section...
I am working on CAF example Module and it has 4 pwms in overlay file.
1. Is it possible to add another PWM?
2. Is there any limit to number of PWMs and number of channels...
We have an existing application, based on the nordic softdevice s140nrf52701 that uses the AES algorithm, specifically ECB, CTR and CBC mode. We need to migrate to AES GCM...
Hi.
I’m trying to install Nordic Semiconductor’s nRF Connect SDK (NCS) version 1.9.2 via the command line. The standard nrfutil tool only supports versions 2.0.0 and above...
Hi,
I referred to the zephyr/samples/drivers/soc_flash_nrf/ code, and when I added CONFIG_BOOTLOADER_MCUBOOT=y , the flash storage started from address 0xfc000 . Why did...
Hi,
For a new product we would like to use Midi over BlueTooth (probably BLE). Is there support for this using some Nordic SDK (like the nRF Connect SDK)?
I can find several...
Hello everyone,
I’m facing an issue with my Thingy:91 . It was working fine throughout the day, but after flashing a program onto the nRF9160 , my computer no longer detects...
Hello. I am using nRF52832, SDK ver 15.3 and running it as a peripheral device. I use an interval timer to send a UART to an external device and receive an ACK. After running...
I am using nRF52840-DK with nrf5-SDK version 17.1.0.
I want to use logging system provided but facing issue due to it's complexitiy.
I am not able to find any example...
